11026112310 Kenmore Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James from PINE MOUNTAIN, GA
- Parts Used:
- 8212641RP
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Washer hoses due for replacement
Replaced each hose. Did discover that either hose can be used for hot or cold water lines. No longer required to label hot and cold replacement hoses.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Danny from HARRISBURG, PA
- Parts Used:
- W10404050
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Washer would not agitate or spin and took over 2 hours to go through all cycles.
Started by replacing the lid latch assembly but this did not fix the problem. Parts Select representative suggested replacing the drive pulley clutch assembly. I order this and a new shift actuator. Had difficulty installing the new black shift actuator as it has a different electrical connection location from the original red part. The plug on the existing wiring harness would not reach the socket on the new black shift actuator. I had to remove the socket from the new black actuator casing so the plug would reach the socket. Washer is now working.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from WARMINSTER, PA
- Parts Used:
- W10404050
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Washer would go into the cycle to rinse dry.
Replacing the part was fairly easy. However it did not resolve the problem. The spin cycle did not activate,leaving my washer full of water. We ordered another Maytag Washer. Hopefully this one doesn't break down for a long time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diana from Chimacum, WA
- Parts Used:
- W10404050
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
door latch broke
Figuring out how to take the lid off was the hard part. Took out the old and replaced with new and put lid back on and rehooked up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from DREXEL HILL, PA
- Parts Used:
- W11244231
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Replace drain hose
At first I had to position the washer so I could get access.. after having it positioned, I figured it out. Getting the clamp fastened, I was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Keenesburg, CO
- Parts Used:
- W10404050
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
The lid lock switch on our clothes washer went out
I had to remove 3 screws from the back of the washer to be able to lift the top. Then remove 3 screws under the lid which held the switch in, unplug the old part and put the new one in. It was quite sinple. The most difficult part was figuring out you have to slide the top of the washer forward a bit to be able to tilt it up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David B from Madison, IN
- Parts Used:
- W10404050, WPW10240513
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Bad latch lock
Took the back of the control panel off, lifted the top of the washing machine up took off nuts holding the latch lock off, installed the new parts put back together. Piece of cake...because i got the right parts the first time. Thank you PartSelect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Lincoln, RI
- Parts Used:
- W10404050
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
would not unlock
Disassembled ,as assembled.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Franklin, IN
- Parts Used:
- W10404050
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Lid lock would not ingague.
Removed two brackets on back top of washer that hold top secure. Pulled top forward and up off off pins located on front top of washer. Located switch removed two screws holding it in. Then removed Panel on back of top in order to get to controls and unplugged other end of switch. Then reversed procedure and waher was back in service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DIANE*RACHAL from SHREVEPORT, LA
- Parts Used:
- W10404050, WPW10248088
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Latch Assembly and lock broke
I taught I might have to replace the whole machine. Then I realize we had power but the latch and lock assembly wasn't locking for the machine to lock and start to wash. Unplug the washer, took the top off of washer, unscrew two bolts from latch assembly, replace latch assembly and two bolts. then unscrew two bolts from lock and replace it. Machine works great now.
Was this instruction helpful to you?
Thank you for voting!