11022532510 Kenmore Washer - Instructions

Pulled cap off top of agitator, loosened bolt down in center of assembly and pulled collar up with pliers.
Removed old dog ears and replaced. Need to be extra careful on direction of dog ears.

Very simple; even a cave man could do it!

got the parts from parts select and got the machine repaired quickly
what a savings
repair man would have been over 100 dollars
the shipping was more than the parts but I saved greatly with no repairman
love your site and the great savings
i really loved my washing machine and hating to lose it
was so satisfied that I could save it after all these years
thanks

Removed the agitator assembly with a socket wrench and extension, replaced cogs, reinstalled assembly...took about 10 minutes because I dropped the assembly once, and had to reassemble it. An absolute "piece of cake."

Removed fabric softener dispenser. Inserted medium flathead screwdriver into slot on side of cover that is on agitator and pried off. Used socket wrench, socket and extension to unscrew bolt inside agitator. Lifted out and slid off plastic ring holding agitator cogs (cogs will fall right out so make sure you check to see how they're in). Replaced cogs in the same direction they came out. Very simple!!

Washer stopped agitating. I removed the clothes softener cup on top of the agitator by grasping and pulling up, inside the agitator I removed the inner plastic cap by grasping the 2 finger tabs and pulling up. There was a plastic retainer assembly with spring instead of the 7/16 nut referred to in other posts. I used a long 1/2" ratchet extension to remove the plastic retainer assembly, removed the top half of the agitator and replaced the cogs, then replaced the agitator, plastic retainer assembly with spring, snapped the plastic cap back on, and replace the clothes softener cup.

Removed the four worn agitator directional cogs and replaced them with new ones

I followed a repair video on YouTube It is easier to disassemble the agitator and replace to cogs The hard part was placing the top part of the agitator back onto the bottom parts, after I replaced the cogs. i use a flashlight to help see where the two separate pieces of the agitator need to be to connect the back together properly ( top agitator & bottom agitator). Once this sep is completed you have to place the whole agitator and line it up on the agitator rod. Line up the groves as much as possible. Turn the agitator slowly until it slides into place. Then use your socket wrench to tighten the screw. The screw is the last step to attach the agitator back onto the washing machine. Then replace the cap, to keep water from going down into the washing machine. Then replace the fabric softener dispenser. Now you have a great washing machine. I am a women and did this repair by myself.

I went on line to find out how take the adjetator apart. You just stand on the adjetator and pull the top off. Very simple. Once that wss apart I cleaned the dog area of dirt and old pieces. Install new dogs and put it back together. I was trying to make much harder than it was. Piece of cake.

Replaced hinge switch. Still no spin cycle. Noticed hinge bearing cracked & if hinge forced into switch, spin activated. Ordered new hinge bearings.Spin cycle still didn't engage. On further examination, observed that hinge was bent. Straightened hinge & worked like a charm. Didn't really need new switch or bearings. NOTE : Avoid having washer door bang shut.Took longer than expected, but each procedure was simple.

Removed agitator according to instructions, although upper and lower agitator did not want to separate. I used a steel rod and hammer to separate them by hitting lower agitator where bolt goes through. After removing and replacing old cogs, cog holder had to be tipped upside down to insert in agitator. I used a small dap of toothpaste to hold retainer in place while I inserted it in agitator. Works great now.

Removed the bolt that holds the agitator in place..pryed the metal ring that holds the agitator dogs in place..replaced the old dogs with the new ones..old ones were broke off so I had to figure out what direction to install them by assembling everything and making sure that the dogs would catch the teeth on the part that surrounds them..reassembled and then the machine wound agitate properly..but then discovered that the direct drive clutch was not working keeping the drum from spinning..so I replaced the clutch but that's another review..

THE INSTRUCTIONS ARE ON THE SAME SITE AS YOUR PART WHITCH MADE IT SIMPLE

removed the agitator and melted the retaining clips to loosen the retainer cover for the cogs. went simple after that.

We ordered the dog Agit clutch and within a few minutes I had a new washer. It started agitating a lot faster.

Part ordered was incorrect even though your website said that it was correct when I ordered it. Part sent back. Have since bought a new washer. Your contact person to return part was very helpful.