11022532510 Kenmore Washer - Instructions

There are a lot of complaints, with these new energy efficient washers, no matter the brand, on the amount of water that is being used, and not properly washing your cloths, while in the wash cycle.
I got this new MayTag washer, and wanted to see it work, for myself, so I can try to correct the problem. But in order to see it work, and fill, the lid has to be open, to observe it working.
To do so, there is a part connected to the lid, called a "STRIKE", that when the lid is down, it activates the electronics, making the washer run.
So, I purchased this strike, to insert it in the washer, so I can observe the washer running, while the lid is open. Very easy, no tools required, just stick it in the slot, where the strike, on the lid goes, when the lid is closed.

see you tube on how too

I have a Kenmore he 500 series washer that would not get out of the sensing mode. Googled the problem. It let me know it could be the water inlet valve. So I ordered the valve through Part select (mailed to me with in days of ordering) Had a towel and small bowl for nuts and screws. Shut off water to washer, disconnected hoses, used screwdriver and socket wrench to unscrew the back of washer (since it was my first time to ever do something like this on my own, I took pictures to make sure everything went back in place) replaced valve. It was an easy connection. Washer works great

had to change out wiring harness was not compatible

Replaced the suspension rods not an easy task but very rewarding to hear it running quiet again when spinning.

I watched the instructions on line, and followed them. Completed the parts change with out any problems, but that wasn't everything I had to do to make the washer to work again. I had to clear all the fault codes that were on the machine. Then the washer started working in all the cycles.

My fault completely! I shut a valve off to a spicket that I have in my garage due to a Nebraska winter. The problem turned out to be that my washer was receiving its cold water from the line that I shut off. So it was an expensive lesson to learn after replacing the switch harness and the latch. Water was turned off Ding Dong!

Was the video and I started everything fell into place. Thank you very much

Removed two 1/4” screws from the backside of control panel. Plastic putty knife slide under front of control panel to release the clips and allowing panel removal. Shut water supply off and removed both hot/cold hoses from valves. Removed the two T-20 screws which allowed the removal of the existing leaking valve assembly. Installed in reverse and it worked perfectly!!

Removed the old and replaced with new

I watched the video and for the most part the first part of the repair went well. I carefully stored the screws, but despite what the video suggested the part did NOT just slide out. Upon further inspection I discovered two small screws in the top of the valve housing affixing it to the machine. Since it was to narrow an are to use a driver I was forced to remove the housing that holds the timer, which involved removing the knob and a small screw. On each side of the housing was a metal clip and true to form I was able to loosen one side but the other the clip launched into orbit. After a thorough inspection of the floor I found said clip. I was then able to remove the housing and loosen the two screws. Of interest is the fact that the new part had molded places for screws different that the video. After that replacing everything went smoothly and I was able to hook up the washer as the repair was successful.

Removed old one (2 screws) slid in place and screwed in.

I removed the cover for the softener dispenser on the top of the agitator. Then reached in and removed the cover of the nut and washer which was very sticky and sealed with an o-ring. This took a bit of pressure. Then used a socket wrench with an extension to loosen the bolt and took the whole agitator out of the machine. Then I set the agitator on the floor and with a fine 12 inch long screw driver released the catches while turning and pulling the agitatior with my other hand and holding the lower agitatior on the floor with my feet. I then turned the upper part over and removed the cogs and holding mechanism.
Then I reversed the process after replacing the cogs with the new part. 25 minutes total.

I ordered the new cogs but didn't want to wait the few days for them to arrive. So I decided to try and temporarily repair the old ones. After looking at the picture of the new ones on this site I realized that the teeth were just worn down. I took all four of them out and used a grinding disc to carve the teeth down deeper. They were not perfect. (I would recommend holding the teeth with a vise.) However, after reinstalling the cogs the machine worked perfect and that was two weeks ago. I'm not going to install the new ones until I have to.

Just watched the video. Take from a 63 year old. Who never fixed a washer. Thx a lot for the video it saved me a lot of money being on a fix income. and it was less than $ 10 that was included shipping.