11023102310 Kenmore Washer - Instructions

First, I unscrewing the single bolt which keeps the two part agitator in place (agitator bolt). Second, I pulled the entire agitator out from the machine. third, I then seperated the top and bottom parts of the agitator. forth, I removed the old worn out "Agitator Direction Cogs". Fifth, I then inserted the new Agitatpr Direction Cogs"s. Six, I reassembling the top and bottom parts of the agitator. Seven, I reinstalled the reassembled agitator back into the machine. Eight, after inserting and tighting up the agitator bolt with a socket rench, and tured the machine on, it work like it was new again. .

very easy to repair , instructions very clear , parts person very good to talk to, parts got here fast

Removed the agitator with a socket wrench and replaced cogs as directed in repair video.

Fabric softener dispenser simply lifts off the top of the agitator. Then, a flat head screwdriver, tucked anywhere under the edge of the cap, lifts/pries it off. Then drop a 1/2" drive extension(no socket as it simply is the extension itself) into the plastic "nut" and remove it while holding onto bottom of agitator with your other hand. Lift it out, replace the cogs and reverse for reassembly. Total time less than 5 minutes, including shipping was $10.50 for cogs - repair #4 completed thanks to the fine folks at PartSelect! PS - part arrived at my door less than 24 hrs after ordering it even tho I requested 2-3 day shipping.

Replaced the water inlet valve. Easy install… figured it out on my own, but checked the instructional online video to make sure it was done right.

Removed the bolt that holds the agitator in place..pryed the metal ring that holds the agitator dogs in place..replaced the old dogs with the new ones..old ones were broke off so I had to figure out what direction to install them by assembling everything and making sure that the dogs would catch the teeth on the part that surrounds them..reassembled and then the machine wound agitate properly..but then discovered that the direct drive clutch was not working keeping the drum from spinning..so I replaced the clutch but that's another review..

repair was really simple. If you can get it apart, you can fix it. the parts fit perfectly.

The repair went smoothy except for removing the screw that holds the upper agitator part from the bottom agitator. Once that was removed all went smoothly. Considering my washer is 17years old, I guess I should be happy that was my only problem. I followed the directions of the repairman in the video that was provided by the web site. Most of my parts matched his parts :). My husband was very proud that I repaired the washer and was able to diagnose the problem. Thanks for helping me save some $$$$. I'm pleased and am very happy to have solved the problem on my own. My husband teases me about hanging a shingle. Thanks, Zina

We ordered the dog Agit clutch and within a few minutes I had a new washer. It started agitating a lot faster.

Removed the four worn agitator directional cogs and replaced them with new ones

Removed agitator according to instructions, although upper and lower agitator did not want to separate. I used a steel rod and hammer to separate them by hitting lower agitator where bolt goes through. After removing and replacing old cogs, cog holder had to be tipped upside down to insert in agitator. I used a small dap of toothpaste to hold retainer in place while I inserted it in agitator. Works great now.

I went on line to find out how take the adjetator apart. You just stand on the adjetator and pull the top off. Very simple. Once that wss apart I cleaned the dog area of dirt and old pieces. Install new dogs and put it back together. I was trying to make much harder than it was. Piece of cake.

I followed a repair video on YouTube It is easier to disassemble the agitator and replace to cogs The hard part was placing the top part of the agitator back onto the bottom parts, after I replaced the cogs. i use a flashlight to help see where the two separate pieces of the agitator need to be to connect the back together properly ( top agitator & bottom agitator). Once this sep is completed you have to place the whole agitator and line it up on the agitator rod. Line up the groves as much as possible. Turn the agitator slowly until it slides into place. Then use your socket wrench to tighten the screw. The screw is the last step to attach the agitator back onto the washing machine. Then replace the cap, to keep water from going down into the washing machine. Then replace the fabric softener dispenser. Now you have a great washing machine. I am a women and did this repair by myself.

THE INSTRUCTIONS ARE ON THE SAME SITE AS YOUR PART WHITCH MADE IT SIMPLE

removed the agitator and melted the retaining clips to loosen the retainer cover for the cogs. went simple after that.