11020102311 Kenmore Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- JOSE from MILLBURY, MA
- Parts Used:
- WPW10006355
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
washer was draining but no spinning
Disconnect electrical plug from the wall, disconnect drain hoses and tip washer forward remove belt hosing basket and then remove the electrical plug that contains seven wires connected to actuator then remove the two small screws.
Then reverse the operation to stall the new part. Very easy.
Then reverse the operation to stall the new part. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lucas from ARKANSAS CITY, KS
- Parts Used:
- W10721967
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Making a loud noise for a while then stopped spinning
Removed two screws to remove guard. Two screws to remove another part with wires. Pulley nut was already missing. Component was twist locking tabs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from LIVONIA, LA
- Parts Used:
- W10404050
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Lid lock not working.
Followed instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from MAHWAH, NJ
- Parts Used:
- WPW10006384
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Burning smell, ASSUMED it was the belt
Once we put the washer on it's side noticed lots of oil on the floor and in the belt cover area. Replaced belt anyway but issue is the leaking transmission. Starting warranty process since Maytag carries a 10-year part warranty and machine is 6.5 years old. Wish me luck !!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kim from MOUNT UNION, PA
- Parts Used:
- WPW10006355
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
washer would not spin on wash cycle
My daughter is the handy one in the family. She followed Steve's video installation steps and in an hour i was washing clothes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maxwell from RINGWOOD, NJ
- Parts Used:
- WPW10006355
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Washer -Maytag Centennial- would NOT agitate. It would run through all cycles as indicated by the lights and even spin at the end, but never agitated. It also did not appeared to go into "sensing" mode at the start. Took a long time to move from "sensing" light to "wash" light. Did not hear or see a
There are a number of videos showing how to do this repair:
>Disconnect power and water - cold, hot and drain.
>Put washer on its side on a stand (low platform) to get to the bottom.
Better than than just laying front of washer on floor.
>Used a drop light to help see bottom.
>Removed Pulley Cover using nut driver - has 2 screws with nut
heads.
>Removed and replaced the Shift Actuator (part provided) using a
Phillips screw driver - 2 green screws. Unplugged electrical
connector which should be reconnected before new unit is screwed
back down.
Replacement part is not the same as the original. From what I read.
this part has been a problem with these washers.
>Put Pulley Cover back on.
>Reset washer upright.
>Reconnected water and power.
>Ran "CALIBRATION". In Diagnostic Test Mode, turned to "rinse"
light on and pushed "start" button.
>Ran "AUTOMATIC TEST". In Diagnostic Test Mode, turned to "spin"
light on and pushed "staet" button. Washer agitated in first cycle
- "sensing" and in "wash".
.
Washer has been working as it should and I a very happy with the results.
I must say that PartSelect Identified the bad part as the Shift Actuator right off from the symptoms I provided.
>Disconnect power and water - cold, hot and drain.
>Put washer on its side on a stand (low platform) to get to the bottom.
Better than than just laying front of washer on floor.
>Used a drop light to help see bottom.
>Removed Pulley Cover using nut driver - has 2 screws with nut
heads.
>Removed and replaced the Shift Actuator (part provided) using a
Phillips screw driver - 2 green screws. Unplugged electrical
connector which should be reconnected before new unit is screwed
back down.
Replacement part is not the same as the original. From what I read.
this part has been a problem with these washers.
>Put Pulley Cover back on.
>Reset washer upright.
>Reconnected water and power.
>Ran "CALIBRATION". In Diagnostic Test Mode, turned to "rinse"
light on and pushed "start" button.
>Ran "AUTOMATIC TEST". In Diagnostic Test Mode, turned to "spin"
light on and pushed "staet" button. Washer agitated in first cycle
- "sensing" and in "wash".
.
Washer has been working as it should and I a very happy with the results.
I must say that PartSelect Identified the bad part as the Shift Actuator right off from the symptoms I provided.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Zoran from ROCKVILLE, MD
- Parts Used:
- WPW10683603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
water inlet valve stopped working
used the Parts.com video. I am not mechanical at all, but removed the old part and installed the new part without a hitch. Very happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Courtney from Hollis, NH
- Parts Used:
- WPW10006355, W10721967
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set
Actuator clicking not going into spin mode
I laid the washer on its front side to access underneath. I removed the original washer pulley system and actuator very easily to replace them with the new parts. The new/updated model actuator for my machine was a little bit challenging to maneuver around existing parts to make work, but I eventually got it installed. The plug was angled very differently than the original plug on the actuator, but it was a tight fit. There was no issue installing the washer pulley system. Hooked washer back up to power, water lines, drain line, and the washer has been working perfectly since.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doris from CONCORD, NC
- Parts Used:
- WPW10683603
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
cold water inlet valve bad
Ordered the inlet assembly from this site. Received it the day after I received the notice it shipped. Watched their video of how to replace the part. Easy job, done in 15 minutes. Only needed a screwdriver to take the cover off the back of the washer control panel. A company wanted $400 to replace the part.
Definitely recommend the company and will use again.
Definitely recommend the company and will use again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from INDIANAPOLIS, IN
- Parts Used:
- WPW10006355
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
would not spin
online videos were great. called to order and lady was very helpful. washer is now operating normal
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Katherine from Saint Cloud, FL
- Parts Used:
- WPW10276397
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Remove and replace drain pump
Unplug unit. Remove back panel. Disconnect drain hose using pliers to squeeze hose clamp. Tilt washer forward to access drain pump. Remove three screws on the pump. Unplug wire connector. Install new pump. Plug in the wiring connector. Reconnect hose. Reinstall back panel. Super easy fix!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kristy from Lebanon, NJ
- Parts Used:
- W10721967
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Washer was making an awful screeching noise when agitating
I turned off and disconnected the water lines (have a bucket ready) and tipped the washer on its back. I followed along with the provided video that was super helpful. Disconnecting, moving the washer, and reconnecting everything took longer than the repair. Very satisfied with this repair!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from BRISTOL, CT
- Parts Used:
- WPW10006384
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Belt needed to be replaced
Took the Cover off and installed belt.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from SAN JOSE, CA
- Parts Used:
- W10404050
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Washer would not adgitate
I ordered a lid switch because the washer wouldn't agitate. Most reviews indicated that was the problem. While waiting for the part to arrive, I discovered the transmission to be of fault.I let parts select know that I no longer needed the part. Parts Select gave me an immediate refund no questions asked and before I returned the part to them. That is customer service!! I will use Parts Select for all my future purchases. I can trust a company that trusts its customers.
Joe M. San Jose
Joe M. San Jose
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from INDIAN LAKE, NY
- Parts Used:
- W10404050
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Lid wouldn't lock
Removed 5 screws on back, released 2 retention clips on front, lifted top of washer to expose lock assembly, removed 2 screws holding lock assembly in place followed electrical line back to plug behind control panel plugged new lock in, and reassembled in reverse order. Done!
Was this instruction helpful to you?
Thank you for voting!