11020222511 Kenmore Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- JERRY W. from CARROLLTON, GA
- Parts Used:
- W10721967
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
making noise when starting spin cycle
Watch video on the site and the insulation will be easy and take about 30 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from MAHWAH, NJ
- Parts Used:
- WPW10006384
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Burning smell, ASSUMED it was the belt
Once we put the washer on it's side noticed lots of oil on the floor and in the belt cover area. Replaced belt anyway but issue is the leaking transmission. Starting warranty process since Maytag carries a 10-year part warranty and machine is 6.5 years old. Wish me luck !!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lucas from ARKANSAS CITY, KS
- Parts Used:
- W10721967
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Making a loud noise for a while then stopped spinning
Removed two screws to remove guard. Two screws to remove another part with wires. Pulley nut was already missing. Component was twist locking tabs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from LENGBY, MN
- Parts Used:
- W10913953
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
screeching noise at times,Wouldn't spin out
Tip washer on its front removed belt guard and belt. Removed shift actuator. Put new actuator on, put belt and guard back on, put back panels on and it was fixed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kristy from Lebanon, NJ
- Parts Used:
- W10721967
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Washer was making an awful screeching noise when agitating
I turned off and disconnected the water lines (have a bucket ready) and tipped the washer on its back. I followed along with the provided video that was super helpful. Disconnecting, moving the washer, and reconnecting everything took longer than the repair. Very satisfied with this repair!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from PINE MOUNTAIN, GA
- Parts Used:
- 8212641RP
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Washer hoses due for replacement
Replaced each hose. Did discover that either hose can be used for hot or cold water lines. No longer required to label hot and cold replacement hoses.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from BRISTOL, CT
- Parts Used:
- WPW10006384
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Belt needed to be replaced
Took the Cover off and installed belt.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Cranford, NJ
- Parts Used:
- W10913953
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Washer would go from sense to done without running cycles. Sometimes the drum would make a quarter turn.
I followed the video published on this site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shane from CLINTON TWP, MI
- Parts Used:
- W10721967
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Rinse cycle kept repeating, did not spin clothes
Spin indicator light was illuminated but machine was repeating rinse cycle rather than spinning water out of clothes. Replaced the pulley and drive coupler, thinking there was a mechanical problem. Video instructions were great but old pulley and drive coupler looked perfect so replacing them did nothing. Next I replaced the washer actuator (shifter), thinking that was the reason for no high speed spin. Easy job, as shown in the video, but it also did nothing. The problem turned out to be a failure in the control panel, probably resulting from years of vibration. Decided to stop chasing my tail and bought a new washer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold from Blaine, WA
- Parts Used:
- W10721967
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Making groaning noise in spin
Having been out of the business for quite a few years I thought that I was dealing with a direct drive machine. Thinking that it was the motor coupler. I removed the control panel and attempted to pull the cabinet froward. Not so, it had a solid cabinet, so I tilted the machine against the wall and looked under the washer finding the driven Transmission pulley loose on the shaft. The splines on the pulley were pretty well worn but I tightened the nut and it worked okay. But I ordered a pulley and replaced after it's arrival. The motor capacitor also broke it's mount off so I had to rehang it with zip ties and repaired the wires to the Capacitor, (Which BTW had about 22 gauge wire). I found it hard to believe that they would use such small wire.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!