11021352112 Kenmore Washer - Instructions

First I came to this web site and discovered some directions from other customers. I then followed those directions to disassemble the agitator. I removed the softener cup by pulling up on the blue plastic retention ring. I then used a flat head screwdriver to remove the plastic cap by placing the screwdriver into the slot on the side and prying it off. Next I used a 3/8 socket and extension to remove the bolt which holds the agitator to the shaft. After the bolt was removed I pulled up on the agitator and removed it from the washing machine. To remove the upper section of the agitator, I placed it on the ground and holding the base with my feet, I pulled on the upper section. I then removed the dog ears, verifyed the problem and ordered the parts (dog ears). The parts arrived in less time than promised, were installed in about 5 minutes and I was back to doing laundry. When you reassemble the agitator, turn it upside down to install the dog ears so they do not fall out.

The repair was very simple. I removed the agitator cap with a small screw driver, removed the retainer screw with a socket set tool. I removed the top agitator, lifted the cam and removed the old worn directional cogs installed the new ones. I reassembled the agitator. All of 10 minutes.... Very easy

I used a nut driver to remove the screw that held the to part of the agitator onto the bottom part. I then took out the worn out directional cogs and replaced them with new ones and re-assembled the agitator and was back in business. The agitator now works the way it should. Easy fix. The only negative part of this experience was that the shipping was twice as expensive as what the parts cost. Very fast shipping from PARTS SELECT .

Removed the agitator with a socket wrench and replaced cogs as directed in repair video.

Unplugged remove hoses remove drain hose turned over on its back remove suspension Springs installed new Springs good backup connected Springs did not solve problem

The repair went smoothy except for removing the screw that holds the upper agitator part from the bottom agitator. Once that was removed all went smoothly. Considering my washer is 17years old, I guess I should be happy that was my only problem. I followed the directions of the repairman in the video that was provided by the web site. Most of my parts matched his parts :). My husband was very proud that I repaired the washer and was able to diagnose the problem. Thanks for helping me save some $$$$. I'm pleased and am very happy to have solved the problem on my own. My husband teases me about hanging a shingle. Thanks, Zina

I basically followed the video that was available on Partselect.
I had trouble getting the top of the agitator separated from the lower but I used a length of 2x4 and gently tapped this with a hammer (so I wasn't hitting the plastic directly with the hammer, never a good idea). I few taps around the perimeter of the upper agitator and it came apart. The rest was quite easy. I replaced the seal since it looked pretty worn when I first removed the inner cap.

After removing the pressed in cap inside the agitator i removed it from the machine with a socket wrench. Then it did not take long to figure out that the two peices snapped apart. then one look at the cogs (referred to as dog ears) i knew they where stripped and where the problem. Icanceled the service call and order the parts myself from this site. So it was very easy and i'm not sure how much money i saved but the bragging rights went along way with the wife, Thanks.

removed the agitator and melted the retaining clips to loosen the retainer cover for the cogs. went simple after that.

Removed the bolt that holds the agitator in place..pryed the metal ring that holds the agitator dogs in place..replaced the old dogs with the new ones..old ones were broke off so I had to figure out what direction to install them by assembling everything and making sure that the dogs would catch the teeth on the part that surrounds them..reassembled and then the machine wound agitate properly..but then discovered that the direct drive clutch was not working keeping the drum from spinning..so I replaced the clutch but that's another review..

THE INSTRUCTIONS ARE ON THE SAME SITE AS YOUR PART WHITCH MADE IT SIMPLE

Removed the four worn agitator directional cogs and replaced them with new ones

I followed a repair video on YouTube It is easier to disassemble the agitator and replace to cogs The hard part was placing the top part of the agitator back onto the bottom parts, after I replaced the cogs. i use a flashlight to help see where the two separate pieces of the agitator need to be to connect the back together properly ( top agitator & bottom agitator). Once this sep is completed you have to place the whole agitator and line it up on the agitator rod. Line up the groves as much as possible. Turn the agitator slowly until it slides into place. Then use your socket wrench to tighten the screw. The screw is the last step to attach the agitator back onto the washing machine. Then replace the cap, to keep water from going down into the washing machine. Then replace the fabric softener dispenser. Now you have a great washing machine. I am a women and did this repair by myself.

I went on line to find out how take the adjetator apart. You just stand on the adjetator and pull the top off. Very simple. Once that wss apart I cleaned the dog area of dirt and old pieces. Install new dogs and put it back together. I was trying to make much harder than it was. Piece of cake.

Removed agitator according to instructions, although upper and lower agitator did not want to separate. I used a steel rod and hammer to separate them by hitting lower agitator where bolt goes through. After removing and replacing old cogs, cog holder had to be tipped upside down to insert in agitator. I used a small dap of toothpaste to hold retainer in place while I inserted it in agitator. Works great now.