11022102311 Kenmore Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Donna from MOUNTAINBURG, AR
- Parts Used:
- WPW10683603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Water inlet and valve froze and cracked
Ordered and replaced the water inlet and valve assembly from this site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rodger from ANDOVER, OH
- Parts Used:
- 80040
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
top part ofagitator not turning.
Followed instructions on website video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Luu from STANTON, CA
- Parts Used:
- 80040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
No problem
That OK , easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Corvallis, OR
- Parts Used:
- WPW10072840
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The cap thingy seal broke and splattered fabric softener.
I pulled out the old cap with my hands and jammed the new thingy into place. The lady of house did the repair. Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from CONCORD, NH
- Parts Used:
- 80040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Agitator was not turning
Repair was simple and quick. Started by removing softener cup and removed bolt holding part that housed dogs. Removed housing and slipped of hold down clamp and replaced the 4 dogs then reversed procedure all took about 8 mins
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sam from Surfside Beach, SC
- Parts Used:
- 80040
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
agitator would not turn
Pop the top off the agitator, remove the bolt, pull off the agitator, pull out the part holding the cogs (dog ears),remove and replace cogs, reassemble. Works great now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nelson from UNIONTOWN, OH
- Parts Used:
- 80040
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Agitation ceased
After a quick Google search I determined how to pull off the softener dispenser and top cover. Removed one bolt and pulled agitator out and apart.. Anyone who has used a socket set can do it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from LANGHORNE, PA
- Parts Used:
- 80040
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
top agitatior was slipping
from start to finish was about 10 minutes. used screwdriver to pop off top cap of agitator. used ratchet with small extension to take out bolt for agitator. removed agitator, placed it on ground for leverage and pulled off top agitator. carefully observed old directional cogs. flipped top agitator upside down removed old worn out/ broken plastic cogs. replaced them with the new ones. hard to screw up they only install one way. kept top agitator upside down and put rest of agitator back on. flipped it right side up and pressed down hard for secure fit. placed agitator back in washer. reinstalled bolt. placed cap back on and was finished...25 year old washer working like new. $2.80 not including shipping...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Penu from SAN MARCOS, CA
- Parts Used:
- 80040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Washer agitator was slipping
Removed the agitator cap, then removed the plastic, spring loaded retaining part (needed a square head tool). Once out, the cog retainer came out, replaced all four cogs, and replaced in reverse. Easy as pie & took 10 minutes!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathon from LOCKPORT, KY
- Parts Used:
- 80040
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Plastic gears wore down not allowing top half of agitator to spin
Popped off top of softener cup. Pulled out screen. Used nutdriver to back out the only bolt holding the agitator on. Pulled it off popped out plastic "gears" and popped new ones in. Put back in reverse order. Done in 5 minutes....worked perfectly! Easy!!! Thanks !!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Lindenhurst, NY
- Parts Used:
- 80040
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Top partion of agitator turned in both directions by hand and was not driven by the motor.
Using the IPB I removed the upper assembly to gain access to the cogs. Turned the assembly over and incerted the new parts and reassembled the pieces in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Depeturie from Madison, AL
- Parts Used:
- 80040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Top of Agitator would not rotate
1. Lift the softener dispenser up and out
2. Lift up the plastic cap underneath
3. See bolt...use ratchet with extension to loosen and remove bolt
4. Remove whole agitator by simply lifting it up
5. Place agitator on floor and separate top from bottom agitator by simply pulling apart
6. See 4 plastic cogs that spin the agitator. Like mine they are probably completely worn/stripped.
7. Replace old 4-cog set with a new 4-cog set. They are small and inexpensive parts! I did this and our machine is working just great!
This also gave me a chance to clean the agitator thoroughly!
2. Lift up the plastic cap underneath
3. See bolt...use ratchet with extension to loosen and remove bolt
4. Remove whole agitator by simply lifting it up
5. Place agitator on floor and separate top from bottom agitator by simply pulling apart
6. See 4 plastic cogs that spin the agitator. Like mine they are probably completely worn/stripped.
7. Replace old 4-cog set with a new 4-cog set. They are small and inexpensive parts! I did this and our machine is working just great!
This also gave me a chance to clean the agitator thoroughly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leo from Yorba Linda, CA
- Parts Used:
- 80040
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Worn out Cogs
I unscrewed the top cap by hand and used a socket wrench to remove the main center unit.
the rest was very straight forward.
the rest was very straight forward.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Michigan City, IN
- Parts Used:
- 80040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
The washer quit agitating
I noticed the agitator didn't "lock up" in one direction to properly agitate the load (which in turn "agitated" my girlfriend. I took the agitator apart to find the dog ears were worn. I ordered some new ones at a cost of about $12 delivered fed-ex and had the new dog ears installed in about 15 minutes saving me a bag of money from the repair man.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jose from lake forest, CA
- Parts Used:
- 80040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
agitator wasn't moving
first remove the cap on agitator(softner),then pull out inside cap (small cover inside),loose bolt in center (you need a 7/16 socket with a long extension) after that pull up the whole assamble out of the washer tub,hold bottom part and pull up agitator ,turn up side down to take out the cogs and holder, replace with new ones and go back on the instructions.
Was this instruction helpful to you?
Thank you for voting!