1105142511 Kenmore Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Alex from SPRINGBORO, OH
- Parts Used:
- W11210459
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Cold & Hot water Valve Replacement
Turn off the water at both the cold and hot. May need an bucket to catch any water left in the lines. Then unplug the washer to kill power of course...Taking off the 10 or so small screws in the back metal cover will get you started. The tricky part is getting the clips off the back top where the knobs are. You will have 2 plastic clips and 2 metal clips, 1 on each side. Take a flat head and ease them up and out....careful not to break them! You can pull the whole control panel away from your work area. Once you have full accuses to the valves its self, it is held in by 2 screw on the top inside a slot. You can now unplug the pigtail harness. Repeat the process in reverse to get it back together and the job is complete. 30 to 45 minutes Max.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jon from LAS VEGAS, NV
- Parts Used:
- W11210459
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
washer not filling with enough water
see you tube on how too
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from GRAIN VALLEY, MO
- Parts Used:
- WPW10006384
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
squeal and chirping while in risne / spin mode
Removed belt cover from bottom of the transmission , remove old belt, clean the pulleys ,and re install new belt. The new belt fits tighter so it did a few time to get the belt fully seated. Re install belt cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from BAKER, FL
- Parts Used:
- WPW10006384, W10721967
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Loose pulley
Tightened up the pulley as the video showed me that might be the issue.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Norbert from PITTSBURGH, PA
- Parts Used:
- W11210459
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
replace water inlet value
had to change out wiring harness was not compatible
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leslie from ROCKY FORD, CO
- Parts Used:
- W11307244
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
The washer would not wash or spin.
I watched the instructions on line, and followed them. Completed the parts change with out any problems, but that wasn't everything I had to do to make the washer to work again. I had to clear all the fault codes that were on the machine. Then the washer started working in all the cycles.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rosemarie from LAS CRUCES, NM
- Parts Used:
- W11210459
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Washer stuck on sensing
I have a Kenmore he 500 series washer that would not get out of the sensing mode. Googled the problem. It let me know it could be the water inlet valve. So I ordered the valve through Part select (mailed to me with in days of ordering) Had a towel and small bowl for nuts and screws. Shut off water to washer, disconnected hoses, used screwdriver and socket wrench to unscrew the back of washer (since it was my first time to ever do something like this on my own, I took pictures to make sure everything went back in place) replaced valve. It was an easy connection. Washer works great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JERRY W. from CARROLLTON, GA
- Parts Used:
- W10721967
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
making noise when starting spin cycle
Watch video on the site and the insulation will be easy and take about 30 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charlie from OAKWOOD, OH
- Parts Used:
- W11307244
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Whirlpool builds junk lid switches don't lasting when you have suffered water! About every 3 months it goes out! Repairman won't come to fix so I do it myself!
Unplug washer
Take back panel off
Un plug lid switch
Take screwdriver snap out switch
Snap in New switch
Plug it in
Replace back panel plug in washer
Wash
Take back panel off
Un plug lid switch
Take screwdriver snap out switch
Snap in New switch
Plug it in
Replace back panel plug in washer
Wash
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from HOUMA, LA
- Parts Used:
- W11210459
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Cold water was not working
Was the video and I started everything fell into place. Thank you very much
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dawn from TOWANDA, PA
- Parts Used:
- W10913953, WPW10006384
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Washer won’t go into spin cycle! Tries too but then stops
Replaced the drive belt and shift actuator but that did not fix the problem! So I ordered a transmission and this still did not fix it! I give up! Time to get a new washer!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TERRY from WAUKEE, IA
- Parts Used:
- W10721967
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
When the washer goes into a spin cycle, I would hear an intermittent loud clattering noise. I think the clutch teeth above (the cup part that is spring loaded) and the belted pulley's teeth below are not fully seating on each other during the spin cycle.
W10721967 Splutch Cam Kit
Assuming the pulley nut was properly tightened at the factory. I think this problem occurs because of ever-so-slight rounding of the splutch cam teeth from the actuator engaging and disengaging over whatever time frame there is before a clattering noise develops.
When I took off the 13mm nut using the adjustable strap tool, it felt tight to me...Was it put on as tight as it should have been at the factory? Who knows. I don't have the torque specification of this nut on that plastic pulley.
Watch the videos to remove and replace the belt cover and belt, actuator and splutch cam kit.
Pay particular attention to tightening up the nut. I put the pulley on and hand-tightened the nut. I used the adjustable strap tool and before I tightened everything, I pushed up on the pulley to press against the spring pressure in order to mesh the teeth together. After the nut was tight, I repositioned the strap tool and gave it another go, further tightening it. You see earlier that day, I only tightened it up once because I thought it was good and tight. I put everything back and within a half-hour it was clattering again and I could loosen the nut I thought was tight by hand! I fooled myself. That's why I did it twice, and don't be afraid to give it a good second tightening effort. Two weeks now and the wife is currently very happy.
Assuming the pulley nut was properly tightened at the factory. I think this problem occurs because of ever-so-slight rounding of the splutch cam teeth from the actuator engaging and disengaging over whatever time frame there is before a clattering noise develops.
When I took off the 13mm nut using the adjustable strap tool, it felt tight to me...Was it put on as tight as it should have been at the factory? Who knows. I don't have the torque specification of this nut on that plastic pulley.
Watch the videos to remove and replace the belt cover and belt, actuator and splutch cam kit.
Pay particular attention to tightening up the nut. I put the pulley on and hand-tightened the nut. I used the adjustable strap tool and before I tightened everything, I pushed up on the pulley to press against the spring pressure in order to mesh the teeth together. After the nut was tight, I repositioned the strap tool and gave it another go, further tightening it. You see earlier that day, I only tightened it up once because I thought it was good and tight. I put everything back and within a half-hour it was clattering again and I could loosen the nut I thought was tight by hand! I fooled myself. That's why I did it twice, and don't be afraid to give it a good second tightening effort. Two weeks now and the wife is currently very happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from KEYSTONE, IN
- Parts Used:
- W10837741
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
wanting to see this new energy efficient washer work, with the lid open
There are a lot of complaints, with these new energy efficient washers, no matter the brand, on the amount of water that is being used, and not properly washing your cloths, while in the wash cycle.
I got this new MayTag washer, and wanted to see it work, for myself, so I can try to correct the problem. But in order to see it work, and fill, the lid has to be open, to observe it working.
To do so, there is a part connected to the lid, called a "STRIKE", that when the lid is down, it activates the electronics, making the washer run.
So, I purchased this strike, to insert it in the washer, so I can observe the washer running, while the lid is open. Very easy, no tools required, just stick it in the slot, where the strike, on the lid goes, when the lid is closed.
I got this new MayTag washer, and wanted to see it work, for myself, so I can try to correct the problem. But in order to see it work, and fill, the lid has to be open, to observe it working.
To do so, there is a part connected to the lid, called a "STRIKE", that when the lid is down, it activates the electronics, making the washer run.
So, I purchased this strike, to insert it in the washer, so I can observe the washer running, while the lid is open. Very easy, no tools required, just stick it in the slot, where the strike, on the lid goes, when the lid is closed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from BELLEVUE, NE
- Parts Used:
- W10837741
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The Washer acted like the lid would not latch and stopped it from cycling.
My fault completely! I shut a valve off to a spicket that I have in my garage due to a Nebraska winter. The problem turned out to be that my washer was receiving its cold water from the line that I shut off. So it was an expensive lesson to learn after replacing the switch harness and the latch. Water was turned off Ding Dong!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anna from TAWAS CITY, MI
- Parts Used:
- W10837741
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lid strike broke
Removed old one (2 screws) slid in place and screwed in.
Was this instruction helpful to you?
Thank you for voting!