Models
>
40249032010
40249032010 Kenmore Washer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Models for 40249032010
Click on the best match to narrow your results.
Diagrams for 40249032010
Viewing 8 of 8
Keep searches simple, eg. "belt" or "pump".
In Stock
Order now and your part arrives by Oct 31
$197.55
This drain pump is designed to remove water from the washer during the drain portion of the cycle. It is recommended to unplug the washer before installation to ensure safety. The Samsung Washer Drain...
Special Order
On Order
$57.11
Shipping bolts are installed through the back of the washing machine, and hold the wash tub and basket in place while your washer is being transported. The tub suspension holds the tub correctly in pl...
In Stock
Order now and your part arrives by Oct 31
In Stock
Order now and your part arrives by Oct 31
In Stock
Order now and your part arrives by Oct 31
In Stock
Order now and your part arrives by Oct 31
$40.69
This oil seal (part number DC62-00223A) is for washers. Oil seal DC62-00223A presses into the rear drum to prevent oil from leaking past the basket spin shaft. Unplug the appliance before installing t...
In Stock
Order now and your part arrives by Oct 31
On Order
In Stock
Order now and your part arrives by Oct 31
In Stock
Order now and your part arrives by Oct 31
In Stock
Order now and your part arrives by Oct 31
Common Problems and Symptoms for 40249032010
Viewing 4 of 4Will not drain
Fixed by these parts
How to fix it
Leaking
Fixed by these parts
How to fix it
Water Filling Issues
Fixed by these parts
How to fix it
Shaking and Moving
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- SCOTT from VERNAL, UT
- Parts Used:
- DC31-00054A
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Code indicating washer was NOT discharging water
Watched the video, procedure was simple and as depicted on the video. Started by using a wet shop Vac to the discharge hose and sucked as much dirty wash water out as possible. Removed the pump,and found the motor did not turn freely. Removed the motor (3 screws) and replaced the motor with new part. Reassembled the washer, everything wor
... Read more
ked as it should. After about 3-4 loads of laundry, the "Not Draining" code / problem returned. Again, sucked out the water with the Shop Vac. Checked the Filter /Cleanout and found it completely packed with MUD. Cleaned that out, and again disassembled the washer. The pump was removed and the remaining muddy gunk was cleaned from the impeller. The 3 drain lines that attached to the pump were inspected for blockage/obstruction and flushed of any muddy residue. Reassembly was quick and easy, and the washer has worked well since. I have no idea how the dirt got into the system with enough dirt to gunk up the system. Recommend keeping more frequent inspections of the cleanout trap.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Peachtree City, GA
- Parts Used:
- DC62-30312J
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
OE error code, water keeps flowing during spin cycle, softener dispenser left half full of water, clothes wet after washer stops
Found a repair video of a Samsung washer that looks like mine (9 years old). Removed two screws from the back of the washer, slid the top a few inches toward the front and lifted it off. Disconnected the two double electrical connections, the two rubber tubes from the solenoids, the cold water hose from the back and removed the two scre
... Read more
ws holding the valve in place. Installed the new valve by reversing those steps, slid the top back into place and secured it with the two screws and viola (as Kelly Bundy would say)! The washer now functions normally. I'm waiting for my next water bill to arrive to see whether the sudden increase in usage decreases to its normal amount. We have three adults and four small children in the household so the washer is constantly in use.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- scott from DEERFIELD, OH
- Parts Used:
- DC62-00202A
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
The drain check valve leaked
The part did not fit this model. The flap part fit the hole but the seal ring is too big. I cut 1\4inch out and used super glue the make it small enough to fit and seal the hose. Make sure you only use a drop of glue and keep the seal even and flat so it will seal
Was this instruction helpful to you?
Thank you for voting!