11015862400 Kenmore Washer - Instructions

Turn washer on its side unscrewed clamps used pliers to slide clamps off of two hoses connected to pump then took clips off that hold pump replaced with new pump and put new clips connected hoses and clamps on new pump turned it back upright job finished

First, I read the previous repair stories, so I knew what step to do first. So, first I took the hose off of the drain, then I removed it from the washer. And as the previous repair story stated, some water came out and I had a towel ready to catch the water that was in the hose. I threaded the clamp onto the new hose, pushed the new hose onto the washer, used the pliers to open the clamp to better clamp the hose onto the washer. Then, placed the drain hose into the drain pipe and it was done! Thanks for such a great site!

I watched the video from the web site, decided that pulling the whole case was more work than needed. I tipped the washer back at about 45 degrees so that I could get under it and braced it so that it would not fall back fwd. Put a medium cooking bowl under the pump, used a channel locks to remove the 2 spring clamps that where around the hoses and slide the hoses off and let the water drain into the bowl. Then used a medium straight slot screw driver to release the clips from each side of the pump and slid the pump off the shaft. If you turn the clips 90 degrees they will slip out and had to remove the upper clip to get the pump out. Lined up the pump and the shaft making sure that the flat side of shaft and pump lined up and slid it on. Reinstalled the pump clips and slid the hoses back on the pump slide the clamps back in place lowered the washer and test ran it for leaks. Great Job NO leaks. Whole job took me less than 30 minutes.

just like video showed really helpfull

I removed the back of the washer, removed the old water inlet syphon, replaced it with the new one, and, with some difficulty, replaced the back of the washer, reattaching all of the parts to it.

diconnected water supply and discharge, unplugged the unit, removed the aggitator, laid the washer on it's back, romoved the hoses from the pump, took out 3 bolts, removed the motor/transmission and replaced the clutch and put it all back together.

Followed the video on the website. I removed the hoses from the pump rather than removing the pump as suggested in the video. Then separated the motor from the transmission and replaced the coupling; then reattached the motor and hoses. Lining up the washer cover and clamping it back on was the most trouble. But all in all, a easy repair.

I was familiar with the Kenmore / Whirlpool direct drive mechanism but at first I could not determine how to release the console. I finally found the end cap trim pieces would pop off revealing the 2 screws that hold the console in place. After removing them the console flips up and over the backboard. I then removed the 2 clips that hold the cabinet to the backboard, unpluged the lid switch connector and then tipped the entire cabinet forward and off the frame. This gives you access to the entire washing machine mechanism.
Next I released the 2 metal clips that hold the pump on and push it out of the way leaving the hoses connected. Next I released the 2 clips that hold the pump on, these clips also have a screw to secure them. I was then able to set the motor to the side without removing any wires.
The coupling parts had broken and were already off of the motor shaft and the input drive shaft of the transmission. I put the new drive parts on and had to tap them down untill they were flush with the end of the shafts. I then put the rubber coupling on the transmission drive end and aligned the motor drive to mate into the other holes in the coupling as I put the two back together. I then re attached the 2 motor clips with screws and reinstalled the pump with it's clips. I then reinstalled the cabinet onto the frame and replaced the cabinet clips. I then plugged in the lid switch connector and flipped the console back over and screwed it down. I then reinstalled the trim caps that had me stumped to begin with. The unit tested out OK.

The water pump had a small leak when washing clothes, and my wife was nagging me about it. I know men, youwere shocked that I said nagging and wife in the same sentence. Me being a man, I would have just left it since it is in the laundry room in the carport.

I turned the washer on its side and felt where the leak was on the pump, went inside and ordered the new pump. It was here in 2 days and it took 15 mins to put it back on with only a screwdriver to snap off the retainers and pliers to undo two hoses.

I told my woman that it was fixed and we have lived happily ever after and we played Appliance Repair Man and I was paid very well for the "House Call" if you know what I mean!!!!!

A label was created and never shipped. Sat there for 2 weeks.
Contacted company for a refund and a Retha’s never been issued.
Terrible service!

I first watched a YouTube video on how to open up the machine. It was a breeze. I removed the part the hose attaches to where the water comes out and into the tub. The hardest part was removing the old hose clamps. Had I known I would have used new clamps. I took off old hose and replaced with the new one, it took longer because of the clamp issue. Otherwise it went fairly easy, to my surprise. Even tho I am a 70 yr old woman I will try to fix what I can. Doing this saved me at least $600. For a new washing machine. I'm so proud of myself.

Just removed the broken part and replace it with the new one.

Replacing the fabric softener dispenser was very easy. It just snaps on. Make sure you line up the tabs with the holes in the agitator, otherwise it will not stay on and will fly off and break in the spin-cycle. This is how the first one broke to begin with.

Removed end caps on control panel, removed two screws, lifted the control panel and rolled it back out of the way.
Undid clips and wire connection and pulled the cabinet off. Replaced the switch and put everything back together.
Easy job but helps to have two people to get the cabinet back on right.

I had to unscrew 2 screws that held the control panel, then remove the 2 end caps, remove 2 screws that held the control panel to the washing machine. I then lifted the control panel and leaned the lower case forward. All this to get access to the ground screw for the lid mount. It sounds like a lot, but actually it was quite simple. I replaced the old switch with a new one and put everything back together just like new. No extra screws or parts that I could not remember where they came from. Thanks Parts Select. Reading the comments from others helped me to realize that I could do the work without worry. The only problem I had was ordering the correct part. That did not happen until I got the correct part number from the old part.