11044936203 Kenmore Washer - Instructions

Repair was described as a simple 5 minute job following the enclosed directions. There were no directions included. Customer service replied they could not provide any instructions. I located a technical manual online and determined the steps necessary to replace the baffles. While some may just click them in, a proper repair requires the control pannel and machine housing to be removed. Then the tub assembly must be removed and the plastic tub separated from the basket. Three screws (one for each baffle must be installed. (I recommend using blue loctite to keep the screws from backing out). The entire process must then be reversed. This is a slightly complicated (note the pencil is to mark the locations of clips for ease of reinstallation. I am an Engineer and this process took over 2 hours and required a significant amount of space to lay out the parts as the machine was totally disassembled. This assembly is best accomplished with 2 people and an entire afternoon without interruption. It can be done by anyone with some mechanical skills, but find the consumer services technical manual first and be prepared to keep track of a lot of small and large parts. This is not the simple 5 minute job described by others (unless you just want to snap the baffles on the basket and not lock them down). In that case go ahead and order a few more sets as the clips will break and the baffles will slide off and you will be replacing them about every 6 months.

First I removed the retainer ring that holds the outside bellows on the frame of the front washer.
I then pushed the bellows inside of the drum of the washing machine in-order to get to the clamp that holds the bellows on the inside of the drum. To pull the clump I had to use a stubby screwdriver and socket drive to loosen the clamp. Once the clamp is loosen I was able to pull the bellows off, of the drum and out of the washing machine. Installation was the reverse of removal.

Inputs on your web site of other people who had replaced this valve assembly helped.
Remove top cover from washer - three socket head screws on rear of machine, (need to move washer forward for access)
Turn off both hot and cold manual shutoff vales on wall. Run washer to take water pressure off from hoses (turn on for water to turn on , and then turn washer off).
Remove both hoses (mark/remember which side is hot/cold, as valve assembly has no markings), from valve assembly, had to use channel locks/adjustable wrench to remove nuts as they were really tight. Check to see if gaskets were OK, would have been nice, if these gaskets are supplied with new valve assembly. Remove screw which holds valve assembly to washer. Slide valve assembly slightly side ways to free it from bulkhead panel. Remove last hose assembly inside washer, attached to valve; remove four wires from solenoids. Keep track of wires (which solenoid).
Replace valve, reconnect internal hoses and wires; install valve assemble on bulkhead panel; attach screw; reconnect hoses; turn on manual valves; check for leaks; briefly turn on washer, check for internal leaks; install cover; push back washer in place.

The baffle just slipped on with no tools required. The best thing was that we received our parts the next day after ordering them, and we just paid for regular shipping!

Removed hot/cold water hoses from back of washer at water inlet valve. Pulled off top of washer by removing 3 screws at back of panel. Noted that water inlet valve had been damaged in move from storage. Pulled off 4 wires, 2 for hot and 2 for cold. Removed 1 screw holding inlet valve assembly to frame. Used pliers to release retainer ring on hose. Removed hose from valve outlet. Reversed process to install new valve.

disconect wayer inlet hoses.remove screws that hold the top cover. This will expose the water inlet valve. remove the defective valve and any other associated clamps,hose etc. test run for leaks.

It was fast and pretty easy to do.

Replaced inlet valve. Took top cover off. Accessed inlet valve. Removed hoses. Replaced valve. Works like a charm.Corrected problem

Turned off power, turned off water supply, removed water supply hoses, removed top of washer, photographed electrical connections, removed intake hose, removed screw from part to the machine and removed valve and replaced. Reverse order to install new part and test water supply.

turned off water valves , disconnected and placed hoses into small bucket . removed top . I then removed screw off old valve , shimmied it out of the hole , removed hose with pliers , slipped off white set of plugs and then black set .. Then I put hose on new valve , placed plugs ( black & white ones ) be sure to mark the correct side .. for me two white were on the right side of valve and black on left side .. placed valve back into its respective spot . attached the screw .. note I sled mine to the right just a bit and all lined up perfectly . Attached hoses , ran test cycle on warm , cold , hot .. All hoses were hooked up correctly and leak free . put lid back on and perfect .. The hardest part , was moving the shelves above my washer , really was super simple . Watch the video twice. You will be able to do it in no time. Saved me 245$ . From my appliance shop the part 150.$ 100 service call and the install fee $ since the install was so easy couldn't be much but .. Its a guesstimate ..You can do it !

My hubby and I replaced the part in about 20 minutes, including moving the washing machine. We love doing household projects like this. We're a great team and putting in this part showed how good we work together. Thanks for the quick response too!

First took a picture and printed after disconnecting machine electric supply and removing top cover. removed screw holding vale in place, removed wiring .removed valve,attached wires to new valve inserted in place attached tubing and installed mounting screw and hoses, checked all again and tested

Removed covers per instruction video provided by website

We do not wish to have our repair published. The part itself was perfect and corrected our leaking problem but we did have difficulty with the installation despite detailed instructions. We appreciate a good price for the perfect part!

easy process: troubleshoot problem on website-- order part--get part--watch "how to replace"video on you tube-- get it done with only a screwdriver--go out for movie and dinner with $$ saved.