1105914201 Kenmore Washer - Instructions

The dryer door has a switch hidden inside the machine housing. The switch has a lever that protrudes and when the door it closed it hits this lever allowing the dryer to activate.

*** Unplug machine ****

To replace: pulled out the lint trap, remove 2 screws under the lint trap. Pry the top open at the front (it's press fit in place and will pry open with a flat screwdriver).

Lift lid up and prop open (like the hood of a car). Find the switch at the front of the machine just above the drum. Remove 2 screws holding the switch in place (from just inside the drum area). Pull off the broken clip bracket, replace with new one and screw it back into place. Be careful not to drop the screws or bracket or they will fall into the bottom and you may never see them again. I can't stress this enough!!

Let the lid down and give it a good rap on the front to seat it back into place, replace the 2 screws under the lint trap. Replace the lint trap. And your done.

Very easy to repair remove top of dryer and took out to screws and put switch back in place replaced screws and put top back on. Easy!!

Loosened two screws in back top of drier and pulled forward and up to hinge top of drier and allow access to door switch.Took out broken actuator spring and replaced with new one,snapped lid back in place and put screws back in hinges and job was done.

Replaced the cap over the door switch so when the door closed the switch was engaged

same as I described above. However i was amazed when the part showed up the very next day...I was expecting maybe 3 or so days later. I wiil absolutely use PartSelect in the future.

Googled dryer won't start! From information on the Parts Select website, I determined it was possibly the dryer door switch. Checked the dryer to confirm status of door switch and found it broken! Ordered part and received it within 2 days (actually ordered on a Sunday and it shipped on Monday with receipt on Wednesday. Unpluged the dryer. Used information from Parts select website to remove two screws from vent filter, used screwdriver to pop the top of dryer at each front corner, removed two long screws from the old switch and replaced the broken actuator on the switch with the new actuator received from Parts Select. Note: It was easier to remove old switch with the wires removed from terminals (just pull off), replacing the wires after securing the switch and actuator back in place. Piece of cake, wife happy, received her king of the roost reward :>)) This is also a good time to clean the lint filter area and the hoses to prevent one of those 16,000 annual dryer fires!!!

The dryer just stopped after a new load of clothes was put in. It appeared to be a power problem as there were not warnings, it just stopped. After checking the power, I suspected it was an electrical interlock problem. After nosing around, I traced the power to the dryer door interlock. Sure enough the switch was fine, but the mechanical lever was worn away. After Googling around for a replacement I found PartSelect.Com. Found the part, ordered it, and I am back in business. My wife is not happy though, as she wanted a new dryer:)

Took top of d then dryer loose then replaced switch actuator put dryer top back in place. Not that hard.

I first noticed that the tab of the door switch snapped off so the safety on/off switch did not work when the door was closed. I temporarily taped the switch closed so I could use the dryer. I found the model number from the unit and easily found the schematic and part description from the website. I placed the order and had the part in a few days. Problem solved. Thank you

I went to internet & got the part & instructions.the shipping cost more than the part. Saved 20.00 & gas.

I noticed that the dryer door switch actuator spring/lever was broken on the door. I researched how to get the top of the dryer cover off, and I took apart the mechanism. I called a local repair shop and they wanted me to buy the whole unit instead of just the switch lever. So I did some research to find the part on the web, and I came across your site. It was very easy to navigate, and I fould the part easily. I saved about 66% by just ordering the lever and not the whole unit. I would without hesitation, buy parts from your website again. The part was shipped and received very quickly. Thanks again!

I thought it might be a damaged switch but when I removed it I noticed a metal clip that was attached to it was broken. The pin on the door pushes against this clip when the door is closed which in turn opens the circuit on the switch. I looked up the model on this website and viewed the parts diagram. There I saw the part I needed and it was listed below along with the cost. Couldn't of been easier. Thanks!

two screws on filter housing and then lift dryer to up like the hood of a car the two screws on actuator, be careful not to drop actuator, if you do use a magnet to retrieve, two screws back in then wire clip top of dryer down and two screws back into filter housing and your ready to dry clothes, not recommended but if you have to dry clothes while waiting for part a clamp on the switch will allow you to use dryer, but be extremely careful because dryer will not turn off when door is opened

Located broken front door safety switch actuator. Ordered new part shown on the diagram. Removed broken part, installed new part, start dryer,runs fine.

I'm a 66 year old lady with no repair experience at all!! I found the part I needed on Parts Select, which I ordered and received in less than 4 days. I watched the video that you've posted on your website which shows in great detail how to do this repair. It looked like a simple fix and it was!! I highly reccomend Parts Select!! Took my granddaughter(held flashlight) and myself less than 30 minutes to do the repair!!!