11042934200 Kenmore Washer - Instructions

Looked at how the old drain pump was installed, then removed it and installed the new one. It was a fairly simple fix. The only feedback were that the parts picture was a little confusing becuase the picture didnt really look like the actual part, so we were unsure if we were ordering the correct part.

Washed three loads and it was ok but then it stopped draining again. I don't know what to do.

We followed another very helpful repair story. Unplug machine. Unscrew top back screws, remove top of washer. Reach inside from the top in the front of the machine. Remove screws holding latch in place, unplug the three plugs attached to latch. Replace with new door latch, screw it in place, replug the three plugs, put top of machine back on, replace screws on back and your'e done! Works great! Job made easy thanks to others helpfulness!

Slid the washer out, took the hoses off and the back panel then the front panel, found coins in the filter tray and a baby bottle plastic cap was sealinhg the drain going into the plastic filter housing (it fits perfectly) removed all the items and put the white plastic screw cap back on the drain. Next problem was the washer walking around the laundry room, upon fixing the drain problem noticed the front shock absorber was unhooked and two on the right side of the machine had leak some grease, rehook the front shock and ordered two new ones it don't walk around anymore and works smooth and quiet now. I also have to add that Parts Select has been absolutely GREAT had the parts, delivered when promised.

Could not have been easier. Have spent more time building kids' Star Wars Lego than this took...

Plastic door hook was broken in half and door lock (DL) error code was showing-- though the hook was still in the door (each half held in by its own screw) and the door actually felt as if it was still latching o.k. After reading some things online, I though it was worth buying new hook since it was cheap, and giving it a try. Got it for a total of about $11.00 a little over 48 hours after placing order. It took about a minute to put it in. Then, tried to start the washer and "Voila"-- same error code still appeared! Read some more stuff online and saw a recommendation for "restting" this error by unplugging and replugging the pink wire harnesses at the back left of the top of the machine, after taking off the top (held on by just 3 screws at the back edge). So I did this (after first unplugging power cord), and this time "Voila", it worked! So I assume the error code was initially caused by the broken plastic hook, but the code stayed in the system (even though I had also tried unplugging the power earlier)- and then was cleared off when I did wired harness unplug/replug operation. So the situation was a little puzzling, but still an "easy fix" overall.

It was an easy fix,all I had to do was pull the washing machine out and remove the top off the washer,leaving everything connected,I cycled the machine to figure out where the leak was in the first place,then unpluged the washer,turned off the water and removed the water lines from the back of the washer(be sure to have a couple towels handy)disconnected the 4 color coded wires from the inlet valve making note of which color went to which relay,disconnected the hose from the inlet valve,and removed the one screw holding he valve to washer.That was all,then reversed the procedure to put it all back together. success! took about 20 min start to finish.

removed top cover,disconnected wires to valve,removed valve and hooked up a washer hose to test valve,one side was leaking,valve would not close.replaced with new valve that I received in 2 days,do not buy after market.

(1) Turn off water valves (2) remove water lines (3) remove three metric star screws from top/back of washer (4) remove to plate (5) remove single screw retaining water inlet valve at back of washer (6) remove electrical connections from water inlet valve and flow meter (7) loosen hose clamps at back of soap dispenser (8) remove assembly/apply new parts (9) reverse above directions. Because the plastic nipple at the back of the soap dispenser was brittle, it partially broke on me. I applied urethane glue to the break and let it dry overnight. Next day I applied marine-grade silicone sealant around the break area. That evening I assembled and then used the washer to test for leaks. Success!

I followed the guy on the video. The only parts that were tough was having the right tools and having enough space to put the new part in. The part was only 70 dollars and I was so proud that I could do it. I am not very handy so if I can do it then anyone can. Plus I saved some money!

I just take out the botton part and fine what part what i need chage and just chage exactly like the old if yoo dot remember all the wires please take pictures and you hava guia to check went you are finished

Made a bad call after googling "bearing squeal for HE 4t" and replaced the bearings and seal on the drum.... Turns out my squeal was coming from the drain pump, didn't realize until after a major tear down and replacement of bearings and seal. Managed to break one of the electrical connectors on the heating element on that repair as well... Compared to the bearing replacement the drain pump was super simple. Lots of good instructions above, the only thing I would add is that if you put a little pressure on the hose clamps and spin them to an easier position to see and get pliers on, they will be much less of a headache. Vice grips were the best tool for getting them released and re-installed. The heating element was pretty easy, loosen the center nut to the end of the threads but don't remove. Use a flat screwdrive to gently pry the unit out. Use a little dish washing soap to lube up the rubber plug on the new one before installing and it slides right in.

First I want to acknowledge Parts Select for their prompt delivery(received parts in less than two days)and their unbeatable prices(approximately 1/3 less than two local appliance repair/parts shops). Repair was straight forward a simple swap of the pump and I saved quite a few dollars.Thanks Parts Select.Any future appliance parts needs will be purchased here.

The washer tech manual stated to: 1) remove the top, 2) control console, 3) front below the door (front load washer), 4) remove the retaining wire, 5) pull back the rubber bellows, 6) remove the three screws and remove the door latch/lock assembly. I discovered that steps 1 through 3 are not required to replace the assembly. Installation is the reverse of steps 4 through 6. That was easy. The difficult part was figuring out how to reset the pressure switch so the drain pump would not start every time you reconnected to the power supply (pressure switch thinks the washer still contains water). With the power disconnected, I disconnected the pressure switch from the central control unit. Then I reconnected the power supply and pressure switch. That reset the pressure switch solved the problem with the drain pump. Washer works fine now.

my son repairtet