11081275200 Kenmore Washer - Instructions

Woulkd have taken alot less time had I not taken off the control board, back...etc. Laying the unit on its back is perfect. Took it out into the garage when I could have done it in the laundry rooom with very little water loss.
1. Removed all hoses connected to top of motor. This was not very easy since the spring clamps had been in the same place for 20+ years. Also removed all wire harness connected to and from the motor.
2. Removed metal clamps from top of motor unit, and removed the plastic "valve".
3. Removed screws holding in clamps on each side of the motor used to hold motor on motor plate. Removed motor. Trick is to make sure that the back clamp stays in place...makes it a little easier when you go to re install.
4. Cleaned out around agitator shaft, and fitted one side of the coupling and the neoprene type joiner on to the agitator shaft.
5. Fitted other side of coupling on to motor...This is where it got a little tough......and then placed motor unit on the motor plate, making sure to line up teeth to neoprene joiner.
6. Replaced clamps on each side of the motor and screwed in nuts holding them in place.
7. Replaced plastic "valve" and the clamps that hold it in placed...back one is a little tough.
8. Reattached hoses to "valve" and hooked all wire harness back into place.
9.Tested perfect...little burning smell on first spin....but works great now!!

There are two screws that hold the switch in place. And two wires connected to the switch. The most difficult part of replacement is to place the new switch and hold it in place to reinstall the mounting screws. The space to work in is limited unless you remove the front panel from the dryer, which I opted not to do.

Found leveling spring loose on bottom of washer, the sheet metal on bottom of cabinet ad rusted through. Drilled new hole in sheet metal and installed new leveling spring. Greased hole with blue marine grease so it will last another 40 years.

I WATCHED YOUR VIDEO AND IT CHANGED OUT VERY GOOD IT WAS NOT AS HARD AS I THOUGHT IT WOULD BE. I HAD TO TAKE IT APART 3 TIMES. HE CHEWEW THE HOSES ON THE PUMP AND THE LITTLE HOSE THAT GOES TO THE WATER FILL CONTROLE. I THINK I AM A WASHER EXPERT.I AM 81 YEARS OLD SO ANYONE CAN DO IT.

Removed the old hoses and screwed on the new hoses.

Followed the video posted on the website. Everything went great - first repair attempt took about 45 minutes. Time consumed mostly due to the straps that hold the motor in place being very difficult to put back on and that the cabinet was a little difficult to replace due to the amount of rust around the bottom of it. Tried out the washer when done, and noticed a burning rubber smell. Took everything apart again, checked it, and everything seemed to be ok (made sure all four rubber feet were in place on the motor) so put it all back together again. Noticed the smell again so took it apart a third time, and when the motor felt pretty warm, decided to do an internet search for "burning rubber smell after replacing drive motor coupling." The answer popped right up - the replacement parts were not solid plastic like the original ones- they had metal on the inside of them, and needed to be tapped, a bit forcefully, with a hammer and socket until flush on the both the motor and transmission axles. Once the parts were flush, the straps that hold the motor in place snapped right on. Still a challenge with the rusted cabinet, but once all together again, worked perfect! Thanks to this site , I have fixed washers, dryers, and refrigerators and used them now nearly 20 years! I showed my daughter and granddaughter how to repair them and they don't hesitate to pitch in and help or handle the repairs on their own - again with much appreciation to this sitefor the accurate "how to" videos, the right parts, fast shipping, and great prices.

We watched a video on YouTube; it was very easy . We had to use the mounting bracket.

Removed screws from top control panel. Tilted panel back. Unsnapped two retaining clips and pulled entire washer cover forward. Turned off water and uplugged washer. Disconnected hot and cold water supply. Disconnected supply tube from water inlet valve. Disconnected electrical hook-ups to water inlet valve. Removed water inletvalve. Installed new valve being careful to use new mounting plate supplied and making sure screw holes line up correctly. Re-connected all disconnects and it works like new!

Remove metal cover; remove pump, remove motor, remove tub spin assembly; remove transmission. Remove clutch be removing retaining ring. Installation was reverse. No problems, part worked like champ.

Note: Called Sears to see if I could get the part locally. Turns our I had to call an 800 number. Lady said that the part was not carried and would have to be shipped from warehouse. Tried to sell me some discharge hoses. Then said the part would cost $65 before S&H. Told her I didn't want to spend that much, she asked how much I wanted to spend and seemed upset when I told her your price. She didn't comp it, just said that theirs was an official part from Sears, blah, blah, blah. Anyway, thanks for the great service!

Disassembled top control console and surrounding sheet metal cabinet per the video from this site. i then used a screw driver to carefully pry up each wear pad location individually and inserted the wood wedge. to about 1 1/2 inch height. rwmoved the old wear pads and popped in the new pads one by one. Closed up the unit and tested the machine . It ran like new. No more noise or viberation

The washer agitated ok, so I figured it wasn't the motor or agitator. Watching the repair videos, I assumed the clutch might be the culprit. The videos are very good, so I should have taken the machine apart and actually looked at the clutch - it wasn't too bad. Trying to put the new clutch on anyway, I noticed it didn't turn on level. I thought it wasn't seated correct, but it was then I realized the shaft was tilting. This would explain the THUMP, and the grinding must be a gear inside the transmission. As much as I hate to get a new machine, given the tremendous downturn in quality, I think that because this machine is old, it is not worth a $200 transmission. Anyone need a brand new (but test fitted so not returnable) clutch?

Put new one on work good, but now can't pump no more .the problem now is the spin cycal broke and I not going to fix it. Thank for the part work good.

Disassembled lower part found nothing wrong.
Started disassembly from the top. Immediately ran into trouble not knowing exactly how the tub was anchored to the drive. Once I got down to the tube and drive block there was nothing I could do to go further. I guessed it was a press fit onto the drive, but there were many instructions and I couldn't be sure. Parts Select expanded drawing was the most useful tool; it was correct omitting a few details. Anyhow, cleaning out my garage I found one of my old gear pullers that I could ring to complete the disassembly. All the sudden I was in business, pulling the washer drum off the drive block and shaft, getting down to the leaky lower seal. A that point it was just a matter of cleaning everything up and buying all the rusted out parts to reassemble. I spent $150-200 on parts, but its completely rebuilt now and runs like a charm. Probably have around 20-50 hours all told, into the repair. Most of this was reading instructions, watching videos, and trying to figure out the rest (3). Doing the actual work spread over time until my wife and sons threatened to throw the thing out. Never. Once I decide I'm gonna do something, I do it. LOL!

Yes, I agree that the actual replacement of the pump was an easy task on this whirlpool washing machine, however, unlike other posters, I had no access through the bottom of the machine. My machine has a solid pan on the bottom. It has a large hole in the center - I think to access the transmission, but no access where the pump is.
So, I had to dismantle the entire enclosure, first the back (about 6 screws, a couple of electrical connections, etc.), then remove the rest of the enclosure to reveal the guts of the machine. I also had to disconnect a small vacuum tube attached to the tub, and remove the control console on top along with the back. It was pretty straight forward, took about two hours to dismantle. Then, the actual removal of the pump was as easy as others have described here - two spring clips and a hose clamp and I had it in my hand. I ordered the new part, which came very quickly - 2 days I think. Then I took another two hours to re-assemble the machine. It works - yeah!
Symptoms - water leak on the floor, it was actually intermittent for a time, so I procrastinated. Then when I actually did the work, I could see the rust trail and follow it to the leaky pump. The pump was actually leaking through the center, where the drive shaft from the motor goes. There is probably a seal between the impeller and the central drive slot that gives out after a while.
New pump in - machine back together - no leaks.

The hardest part was removing the machine's cabinet. 2 screws on either end of the control panel, tip the control panel back out of the way and remove 2 clips, then slide the cabinet off the front. Replacing the valve was very easy. I didn't need the mounting plate that came with it. At first it looked like the screw hole wasn't going to line up with the hole in the back of the machine, but then I noticed that the valve had a groove that allowed it to slide downward on to the back. Pretty easy overall.