1106733100 Kenmore Washer - Instructions

I losened the two screws under the flap covering the filter or lint screen. With the screws removed the entire top of the dryer slides forward and hinges up allowing access to the door switch. The door switch is removed by taking two screws out with access obtained by opening the dryer door. Replacing the bracket/switch was easy and a simple reverse of the disassembly put the dryer back together. I would highly recommend doing this repair yourself.

The Door Swith Acuator Spring was broken. I unplugged the dryer. Removed the two screws on the top control panel. Lifted the top of the dryer and propped it up. Then removed the two wires attached to the door switch (remember to label them with tape-one without and one with tape). Then as suggested by a previous "repairman" loosen the two screws that hold the switch just enough to remove the actuator. You do not have to completely remove the screws. Slip in the new actuator and reverse the process. Voila ... you have a new dryer and a very happy better half. I was given a kitchen pass to play golf and savor some "spirit" water.

Advice: Don't slam the dryer door. The actuator will last longer.

Very easy to repair remove top of dryer and took out to screws and put switch back in place replaced screws and put top back on. Easy!!

same as I described above. However i was amazed when the part showed up the very next day...I was expecting maybe 3 or so days later. I wiil absolutely use PartSelect in the future.

Took top of d then dryer loose then replaced switch actuator put dryer top back in place. Not that hard.

I first noticed that the tab of the door switch snapped off so the safety on/off switch did not work when the door was closed. I temporarily taped the switch closed so I could use the dryer. I found the model number from the unit and easily found the schematic and part description from the website. I placed the order and had the part in a few days. Problem solved. Thank you

I just remove two screws slip the old off and slip the new one on replace the two screws back put top of dry back in place replace two screws from dry lint trap

I noticed that the dryer door switch actuator spring/lever was broken on the door. I researched how to get the top of the dryer cover off, and I took apart the mechanism. I called a local repair shop and they wanted me to buy the whole unit instead of just the switch lever. So I did some research to find the part on the web, and I came across your site. It was very easy to navigate, and I fould the part easily. I saved about 66% by just ordering the lever and not the whole unit. I would without hesitation, buy parts from your website again. The part was shipped and received very quickly. Thanks again!

Replaced actuator switch lever. Exact replacement. Worked like a charm.

I went to internet & got the part & instructions.the shipping cost more than the part. Saved 20.00 & gas.

I thought it might be a damaged switch but when I removed it I noticed a metal clip that was attached to it was broken. The pin on the door pushes against this clip when the door is closed which in turn opens the circuit on the switch. I looked up the model on this website and viewed the parts diagram. There I saw the part I needed and it was listed below along with the cost. Couldn't of been easier. Thanks!

I am one Happy Gal.....Looked to fix,thought about just buying a new dryer..In the end talked to the local repair guy...said I could do it myself. (why pay him)..I live in small town.Ordered your part,watched the video and did it...Saved myself over $500, plus the $125 for delivery.for that new dryer..(Small town in the forest!)Very easy to install....Hope to use this dryer for many months perhaps years..It is 30 years old! Works like a champ! Thank You!

Located broken front door safety switch actuator. Ordered new part shown on the diagram. Removed broken part, installed new part, start dryer,runs fine.

My wife did the repair. Went on your website and watch the video on how to replace the switch and she was able to do it herself. I didn't mind at all. Saved $75.00 service charge.

removed 4 screws. 2 in the back and 2 at the lint screen door. Remove top lid of dryer and looked down and there was the door switch with the broken actuator spring. A diagram of the dryer with part locations is very helpful. I checked the switch with volt meter to make sure it was ok. It was ok! Replace the actuator and put every thing back together and dryer works just fine. Thanks to PartSelect I was able to buy the actuator spring buy itself and not have to buy the switch also.