11026952690 Kenmore Washer - Instructions

First, I read the previous repair stories, so I knew what step to do first. So, first I took the hose off of the drain, then I removed it from the washer. And as the previous repair story stated, some water came out and I had a towel ready to catch the water that was in the hose. I threaded the clamp onto the new hose, pushed the new hose onto the washer, used the pliers to open the clamp to better clamp the hose onto the washer. Then, placed the drain hose into the drain pipe and it was done! Thanks for such a great site!

After removing the 2 phillips screws at the base of the control panel, I flipped the panel toward the back. Using a screwdriver, I popped off the spring clips, releasing the cabinet. I removed the 1/4" hex head screw on the spring mount and removed the old spring and replaced with the new. I repeated this with the other 2 springs. The spring bracket in the rear also holds the tub balancing spring. It is easily replaced while replacing the suspension spring.
If this didn't fix the problem, we were going shopping for a new washer. After this repair, it operates like new!

Remove the washer case/enclosure to expose all the internal parts. Lie on the floor and with pliers and a strong arm. Remove and replace each spring one at a time. Pretty straightforward.

Pulled the machine out. Tilted is back, had my son hold it up. Took pliers pulled off hose clamps, used flat head screw driver to pop off clips. removed pump. Then did it all in reverse.
Piece of cake.

I did the repairs after watching a few videos on this web site and it covered everything I needed. Went well and the parts were perfect.

Followed the video on the website. I removed the hoses from the pump rather than removing the pump as suggested in the video. Then separated the motor from the transmission and replaced the coupling; then reattached the motor and hoses. Lining up the washer cover and clamping it back on was the most trouble. But all in all, a easy repair.

Unplug electrical cord, disconnect water inlet hoses and drain line at rear panel. Move washer to garage or larger work area if necessary. Disconnect control panel from top of washer cabinet by removing the two screws at the front corners of the control panel. (The control panel can now be flipped up and back when you are ready to remove the cabinet assembly.) Disconnect the rear panel from cabinet assembly by removing attaching screws at bottom of rear panel (and along the vertical edges if any screws are installed there). Either slightly lift the rear panel up off of the two clip brackets that attach it to the rear top edge of the cabinet assembly, or if need be remove the clips from the cabinet slots. With the rear panel loose, slide the control panel assembly slightly towards the rear and up to disengage it from the cabinet slots, then tip it up and back, away from the cabinet. The cabinet assembly (with top attached) can now be tipped forward and away from washer to expose the internal workings. (It may be necessary to support the rear panel and/or control panel.) The water pump is attached to the front of the motor by two spring clips. Disconnect the two water lines from the pump, then remove the two spring clips. Pull the pump forward off of the shaft extending out of the motor. Install the new pump, then assemble the washer in reverse order. (I was unsure where the leak originated on my washer so I completely removed the rear panel which entailed disconnecting from it the electrical cord fitting, drain and input water fixtures and various other brackets. Pump replacement can be accomplished without completely removing the back panel.)

diconnected water supply and discharge, unplugged the unit, removed the aggitator, laid the washer on it's back, romoved the hoses from the pump, took out 3 bolts, removed the motor/transmission and replaced the clutch and put it all back together.

I removed the back of the washer, removed the old water inlet syphon, replaced it with the new one, and, with some difficulty, replaced the back of the washer, reattaching all of the parts to it.

just like video showed really helpfull

I was familiar with the Kenmore / Whirlpool direct drive mechanism but at first I could not determine how to release the console. I finally found the end cap trim pieces would pop off revealing the 2 screws that hold the console in place. After removing them the console flips up and over the backboard. I then removed the 2 clips that hold the cabinet to the backboard, unpluged the lid switch connector and then tipped the entire cabinet forward and off the frame. This gives you access to the entire washing machine mechanism.
Next I released the 2 metal clips that hold the pump on and push it out of the way leaving the hoses connected. Next I released the 2 clips that hold the pump on, these clips also have a screw to secure them. I was then able to set the motor to the side without removing any wires.
The coupling parts had broken and were already off of the motor shaft and the input drive shaft of the transmission. I put the new drive parts on and had to tap them down untill they were flush with the end of the shafts. I then put the rubber coupling on the transmission drive end and aligned the motor drive to mate into the other holes in the coupling as I put the two back together. I then re attached the 2 motor clips with screws and reinstalled the pump with it's clips. I then reinstalled the cabinet onto the frame and replaced the cabinet clips. I then plugged in the lid switch connector and flipped the console back over and screwed it down. I then reinstalled the trim caps that had me stumped to begin with. The unit tested out OK.

unscrewed a bolt, pulled top agitator out and replaced parts and reinstalled.

Disconnected old power cord inside control cabinet, removed strain relief , then removed damaged power cord. Reinstalled new cord with new strain relief.

I had to unscrew 2 screws that held the control panel, then remove the 2 end caps, remove 2 screws that held the control panel to the washing machine. I then lifted the control panel and leaned the lower case forward. All this to get access to the ground screw for the lid mount. It sounds like a lot, but actually it was quite simple. I replaced the old switch with a new one and put everything back together just like new. No extra screws or parts that I could not remember where they came from. Thanks Parts Select. Reading the comments from others helped me to realize that I could do the work without worry. The only problem I had was ordering the correct part. That did not happen until I got the correct part number from the old part.

Removed end caps on control panel, removed two screws, lifted the control panel and rolled it back out of the way.
Undid clips and wire connection and pulled the cabinet off. Replaced the switch and put everything back together.
Easy job but helps to have two people to get the cabinet back on right.