11084390800 Kenmore Washer - Instructions

Order the part and put the new part on and put the washing machine cabinet back on and check the washer for the water filled up and then it's starting to go on the spin cycles.

Turn off water, unplug machine
Disconnect water lines to the valve
Unscrewed the clear plastic tabs on the top of the machine, then pryed the back away from the top white part.
Two gold clips can be popped out with a long flat head screw driver.
Pulled the back away from the machine enough to disconnect the wires from the valve. Unscrew the screw(s) from the valves.
Old valves out, new valves in. Plug in the wires, screw in the screws.
Then, to get the gold tabs back in place.....i called NASA.
just kidding. They're tough!
I slipped one into the back and held it in place with my thumb. Then I lined the piece up with the slot inside the machine. Then, i pryed the top white part away as I pushed them together. Stuck a long handle screwdriver down in and pushed REALLY hard on the gold tab to get it to snap into place. Everything is really tight, so you might have to try it a few times.....i left some blood behind.
repeat for the other side, snap in the clear tabs, hook up the water lines, plugged it in......
Then I sat back and listened to my wife praise me for fixing her machine!

1- Remove power connection, remove water connections. 2- Remove the top controller box and free it from its hinges. 3- Loosen the back cover to get access to water valve assembly. 4- Remove hose clamp connected to inlet water valve. 5- Remove the old water valve which is secured with 1/4" screw. 5- For installation perform step 5 to 1 and then test your Installation.

Replaced lid switch, but problem still continued.

Replace front legs. Very easy fix.

Unplugged the power while the washer was running, and the water kept on running. The water inlet valve was stuck open. I removed the inlet valve and you cold blow air thru it, it should be closed with no power applied.Ordered replacement from this site it was a perfect fit. As far as the removal and installation procedure, just follow the video as presented on this site. Good Look.

We got the parts, watched your video a couple of times and then began the repair. It went well with one exception. None of my socket extensions were long enough to work well. The required length might be added to the video and the printed installation instructions. Also it would have nice to have been able to order a small tube of the recommended lubricant. Overall I was very pleased. Jack

Ordered the correct part, watched a YouTube video.

1- Unplugged washer. 2- Turned off water supply to hoses hot and cold. (marked hoses H C) 3- Unscrewed hoses to washer. 4-Used phillips head screw driver to take out screws(2) at corners of washer. 5- Slid top of washer forward and lifted top off. 6- Took out retaining clips on each side of washer. 7- Slid frame of washer outward exposing rear panel of washer for access to water inlet valve. 8- Used 1/4" drive to take out screw to inlet valve. 9- Removed inlet valve, unplugged the two connectors and removed clamp from hose to valve. 10- Replaced new inlet valve and reversed the process to assemble washer back together. Total time for repair, about 45 minutes. I now have full running cold water to washer. Thanks guys for the video you provided. Would purchase again if needed. Thanks again!!! Water Inlet Valve with Mounting Bracket Part Number: PS334646

Followed by installation on line

I got a few hints from YouTube (how to remove the washing machine casing) and rest was very simple

received valve as ordered a simple installation. everything went well.home owner can do this repair

Replaced hinge switch. Still no spin cycle. Noticed hinge bearing cracked & if hinge forced into switch, spin activated. Ordered new hinge bearings.Spin cycle still didn't engage. On further examination, observed that hinge was bent. Straightened hinge & worked like a charm. Didn't really need new switch or bearings. NOTE : Avoid having washer door bang shut.Took longer than expected, but each procedure was simple.

unplug unit first Took water & drain hose loose, used two wheel dolly, took washer out on patio. Removed water hose. Removed two screws # 49 an laid back control unit then Removed 2 #6 Clips Top of unit, then pried back unit cover out enough to remove Water valve after removing #4 screw that holds unit to back panel ,removed hose clamp #21 an electric connections, install new water valve and put back together..DO NOT TAKE BOTTOM SCREWS FROM BACK PANEL, if so the bottom will drop.. Intake cold water valve was half stopped up. Also new water lines.

The valve was easy to change, but we as homeowners should change the hot and cold hoses just like they say you should every 5 years. The hoses grew to the water valve and it was almost a disaster. After cutting the end with a dremmel and clamping visegrips on it I finally got it loose. After that it went smooth. Thanks for getting me the part so fast.