11092491400 Kenmore Washer - Instructions

Coupler is design to break when washer is overloaded or out of balance. Saves the motor from being burned out. Very easy repair. Unhook washer hoses and electrical plug...tip washer on side if there is no bottom to washer instead of removing side panels. Unhook clamps to water pump using flathead screwdriver. Water pump comes off without unhooking either of the two hoses. Remove 2 electrical connections and two clamps from motor using socket and screwdriver. Motor pulls out very easy...make sure you are holding motor so it does not drop onto floor. Remove motor mounting plate with socket. Remove old coupling using stubby flat screwdriver from both motor and transmission shafts. Install new coupling on transmission by placing a large socket onto plastic piece of new coupling and tapping lightly with hammer until flush with shaft. Install rubber piece of coupling...tap new plastic piece onto motor shaft using socket and hammer. Reinstall motor mount. Turn motor shaft so coupling pieces are aligned. Reverse order to reinstall motor and pump. I tilted the tub slightly when reinstalling the motor and pump as it is a tight fit...just be patient during this step.

The last step in this process is to go tell your wife that she in fact is NOT getting the new $2000 front loading washer and dryer set she saw at Lowes because you just fixed her washer for $20 including shipping.

It really is an easy fix...takes longer to unhook and move the washer than to replace part. Thank You Partselect for your excellent website and speedy shipping of product.

Unscrewed the remains of the broken knob, and replaced it witrh the new one from you guys. Your service is great. Thanks.

I tried to remove the outer console to get to the tub wear pads easier. This proved difficult for me for some reason. So I tipped the machine on its back at about a 45 degree angle. You will see the tripod support holding up the tub. The pads lie in between the bottom of the tub and on top of the tripod support . You won't be able to see the pads since the are on the top of the support, but you will see the two insert tabs of each pad sticking out. There are about 120 degrees apart from each other. I pushed up on the tub and slipped the piece of wood in between the tub and tripod support close to the pad. Taking a screwdriver and hammer I punched out the wear pad insert tabs. You can replace the old pad with the new one by using some force with your hands. Some pop right in and some you need to use a little leverage, maybe with the piece of wood you used to hold up the tub. Be careful not to get the pads greasy, keep clean as possible. Worked great.

Sprayed wd40 - limescale - boiling water , NOTHING WORKED after half an hour reapeted spraying and pulling the tub and shaking it back and forth - still nothing
Finally I replaced the center nut loosely than putting a piece of wood on top of it and with me holding the tub slightly high - my wife than whacked it hard several times , I also was turning the tub every whack
When it came out it was full of rust and grime - it would have never come out without what we did
Replacing the the rubber washer was easy - machine works and no more leaking- thank you for your video which really helped to start the job

Unable to get information from Part Select on how to use the part that they sent. Part had no grooves. Part Select people were very nice and offered refund but I got the directions from somewhere else. Used needlenose pliers to hold timer shaft and remove the part with the grooves. After 21 years, the shaft was very fond of the grooved part, so it took some doing but it came off. Was able to screw the new part onto the threaded shaft underneath. Success!

Unplugged washer. Pulled the washer away from the wall & leaned it back against the wall to access the underneath side of the washer. Disconnected water hoses to the pump with water pump pliers. Have drain pan handy to catch the water, approximately 1 qt. Remember which hose goes to the proper place. Removed two retaining screws/straps allowing the motor to be seperated from the transmission. There is enough slack in the wiring to allow you to drop the motor without disconnecting. You do not need to remove the water pump. Removed old coupling & replaced with the new one. Make sure you use the "new style" replacement coupler or you will be doing this repair again very soon! Schematics are available online.

Siphon break kit keeps washing machine from continuing to siphon after rinse/cycle -- like emptying a pool with a hose. Fixed the problem of the tub never filling due to siphon draining out water as it's being put in.

On this model, no need to tip washer on back. Tilt console back and disconnect lid switch. Remove two clips holding back to top of washer (under console). Then remove top and front as directed in the video. The pump is accessible from the front of the unit, just below the tub. Hose clamps are easy to remove/replace. Took more time to wipe inside of washer clean than to remove/replace the water pump. Total time was just over 30 minutes.

Watched the video on the website... and did what it said to do. It was VERY helpful... It did not fix the problem... so now I'm on to the next possible solution. Also, provided by the website. The valve was the problem 85% of the time. The water level switch is the problem 10% of the time. The water level switch is what I ordered next.
Ordering is EASY and delivery is fast with available tracking of the shipment. Very nice...! -Eddie Campbell

Removed old tube and replaced with new version. Replacement slightly different than original since the new part included a feature that appears to prevent the problem. New part still fit and is operating well so far.

The coupling, made of plastic and rubber, on our Whirlpool washer gave out. Done the same repair nine years ago and knew what to do. Here is a short summery:

1. unscrew the 2 screws that hold the control panel on top of the machine in place

2. unscrew the screws that connect the housing with the back panel

3. pop the 2 clips under the control panel to release the back panel

4. with the back panel loose disconnect everything
that is pushed, screwed or clamped on and take the back panel off (don't worry about remembering where things go, everything can go only one way together again)

5. slightly lift the housing of the washer in the back to remove, that gives you access to the coupling in front of the machine

6. I personally like to put the washer on its back and do the repair that way. However, if you want to
leave it standing that is gets you there too.

7. take the screws out of the brackets that hold the pump (the thing with the two hoses attached to it)
in place and snap off the brackets; lift up the pump and put aside

8. you can now remove the broken coupling

9. check for any fragments and clean off what needs to be cleaned

10. replace the coupling

11. reverse the order of steps 1 to 7; make sure that the all electrical connections and hoses are connected!

12. test

The instructional video that was attached with the part I purchased was spot on with very simple instructions. The inlet valve came with a metal bracket that was not needed for my model, so just tossed it. Was completed with replacement in about 30 minutes with help from my aspiring handywoman wife (would have taken 15 minutes without her)

Replaced the springs after watching the video's from this site and problem has been solved.

EXACTLY as your video demonstrated.

I just replaced the spring just like the vid show me.it run's like a new one-I bought it used about 5 yr's ago