1106404950 Kenmore Washer - Instructions

The dryer just stopped after a new load of clothes was put in. It appeared to be a power problem as there were not warnings, it just stopped. After checking the power, I suspected it was an electrical interlock problem. After nosing around, I traced the power to the dryer door interlock. Sure enough the switch was fine, but the mechanical lever was worn away. After Googling around for a replacement I found PartSelect.Com. Found the part, ordered it, and I am back in business. My wife is not happy though, as she wanted a new dryer:)

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

I losened the two screws under the flap covering the filter or lint screen. With the screws removed the entire top of the dryer slides forward and hinges up allowing access to the door switch. The door switch is removed by taking two screws out with access obtained by opening the dryer door. Replacing the bracket/switch was easy and a simple reverse of the disassembly put the dryer back together. I would highly recommend doing this repair yourself.

The dryer door has a switch hidden inside the machine housing. The switch has a lever that protrudes and when the door it closed it hits this lever allowing the dryer to activate.

*** Unplug machine ****

To replace: pulled out the lint trap, remove 2 screws under the lint trap. Pry the top open at the front (it's press fit in place and will pry open with a flat screwdriver).

Lift lid up and prop open (like the hood of a car). Find the switch at the front of the machine just above the drum. Remove 2 screws holding the switch in place (from just inside the drum area). Pull off the broken clip bracket, replace with new one and screw it back into place. Be careful not to drop the screws or bracket or they will fall into the bottom and you may never see them again. I can't stress this enough!!

Let the lid down and give it a good rap on the front to seat it back into place, replace the 2 screws under the lint trap. Replace the lint trap. And your done.

Loosened two screws in back top of drier and pulled forward and up to hinge top of drier and allow access to door switch.Took out broken actuator spring and replaced with new one,snapped lid back in place and put screws back in hinges and job was done.

Very easy to repair remove top of dryer and took out to screws and put switch back in place replaced screws and put top back on. Easy!!

Screwed in light bulb and glass protector

very easy

Googled dryer won't start! From information on the Parts Select website, I determined it was possibly the dryer door switch. Checked the dryer to confirm status of door switch and found it broken! Ordered part and received it within 2 days (actually ordered on a Sunday and it shipped on Monday with receipt on Wednesday. Unpluged the dryer. Used information from Parts select website to remove two screws from vent filter, used screwdriver to pop the top of dryer at each front corner, removed two long screws from the old switch and replaced the broken actuator on the switch with the new actuator received from Parts Select. Note: It was easier to remove old switch with the wires removed from terminals (just pull off), replacing the wires after securing the switch and actuator back in place. Piece of cake, wife happy, received her king of the roost reward :>)) This is also a good time to clean the lint filter area and the hoses to prevent one of those 16,000 annual dryer fires!!!

First I popped open the top of the dryer so I could see the part. I removed two screws from inside the door that hold the spring lever and switch together. I removed the spring lever which is also like a bracket that holds the switch in place. Put the spring lever back in place over the switch and reinserted the two screws. Done in about 10 minutes.

The door would not close after installing gasket. Used liquid soap around edge of gasket, this worked.

I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

I first noticed that the tab of the door switch snapped off so the safety on/off switch did not work when the door was closed. I temporarily taped the switch closed so I could use the dryer. I found the model number from the unit and easily found the schematic and part description from the website. I placed the order and had the part in a few days. Problem solved. Thank you

Took top of d then dryer loose then replaced switch actuator put dryer top back in place. Not that hard.

Replaced actuator switch lever. Exact replacement. Worked like a charm.