11074412100 Kenmore Washer - Instructions

Removed two screws holding top control section on, and folded back the control panel. Removed two clips holding cabinet on, tipped cabinet toward me and off. Removed and replaced water valve, being careful to mark hot/cold hoses, and secure the internal hose to the valve with the spring clamp. Most difficult part was lining back up the cabinet when putting it back on the base, but a few minutes to line up tabs and get the front of the cabinet UNDER the front groove in the base got it secure. Works fine now.

My dryer is 35 years old and thought this was it, but I googled the question and found out it was the door switch. Orderd the part and received it very fast and didn't want to wait for my husband to come home so I went on you tube and found a video how to open dryer and change switch. I did it in about 30 min. and yes it is now perfect again. No problems. I just unscrewed the old switch and put the new one in. Maybe I'll get another 35 years out of this machine. :o) Thanks for making it so easy.

Two screws holding top, unhook wire conector. remove cabinet,replace switch. Reassemble.

1. Unplug washer, close hot and cold water supplies and remove water hoses from washer inlet valve.
2. Remove two screws at the bottom of the front of the control panel.
3 Remove two screws at the top of the back side of the control panel.
4. Remove control panel.
5. Remove two retainer clips that hold the back panel to the top of the cabinet by prying them out from the front with a large screwdriver. (Probably the most difficult part of the job.)
6. Use a socket or nut driver to remove the two screws that hold the valve to the back panel.
7. Lift the cabinet from the bottom rear and tilt the cabinet forward until you can access the valve.
8. Remove the wire harnesses from the hot and cold valves taking note of the wire orientation. (The red one will go back on the hot valve.)
9. Use pliers to open the hose retainer clip and slid the clip out of the way and remove the hose from the valve.
10. Reverse the process and you are done!

Initially, we thought the problem was in the water inlet valve and we changed it out. It went OK although the Kenmore almost fell apart after the removal of a few screws and the control unit.
Only thing was that it was unncessary. The real problem was not in the cold water turn on valve, but in the hose. The hose was special in that it was designed to shut off under emergency conditions. It appeared to be able to passs water when tested at my sink, but when connected to the washing machine and under presssure, it would not pass water. I had installed the part by this time so I left it there. I found the Kenmore washing machine rather flimsy in it's construction and tended to totally come apart once a few screws were removed.

The replacement of the water inlet valve was not too difficult after reading the steps posted by others. The main step is to unscrew the top control panel first, remove the top 2 screws of the back panel, and you have easy access to the water inlet valve. No need to remove the entire back panel. Follow the instructions which accompany the replacement water inlet valve and you should have no problems. The washing machine now fills faster with the replaced water inlet valve. The replacement inlet valve arrived within 2 days of ordering! Thanks for the superfast shipment!

I had to call in to find the correct part because the online recommended part looked very different, and the one found using the model number had no photo, so I was VERY leary of ordering. The service rep said that Kenmore products did not always show up correctly and he gave me the part number needed and there was a photo. The part was not exactly the same, but looked very similar and it was more than 50% less than the original recommended part and part with no photo. I thought that the problem finding Kenmore parts was odd since Kenmore is like number one, right? Part took 3 days to arrive, which I thought was great. Turned off power and water. Removed water hoses. Removed three screws from the back of the top (front loader). Removed the top. Removed a screw holding on the water inlet valve from the outside of the unit through the back cover which required a star driver. Unattached the 4 electrical leads. Unattached the outlet water hose (held on with a squeeze type metal clamp -not sure of the exact name for these). The problem that I had was that the water outlet hose bib attachment was slightly larger than the old one, so the hose would go back on, but the clamp was too small so I cusses a lot before figuring out the problem. I had to go and purchase a new larger clamp. After that, I simply attached the electrical connections and put the outlet back on. One other small problem was that the place where the screw through the back cover was originally attached no longer lined up with the new valve. The plastic piece was shorter than the old one so the screw hole did not line up with the hole in the back panel. The screw isn't really necessary. Overall, replacing the part was easy and I was pleased with the process.

1- Unplugged washer. 2- Turned off water supply to hoses hot and cold. (marked hoses H C) 3- Unscrewed hoses to washer. 4-Used phillips head screw driver to take out screws(2) at corners of washer. 5- Slid top of washer forward and lifted top off. 6- Took out retaining clips on each side of washer. 7- Slid frame of washer outward exposing rear panel of washer for access to water inlet valve. 8- Used 1/4" drive to take out screw to inlet valve. 9- Removed inlet valve, unplugged the two connectors and removed clamp from hose to valve. 10- Replaced new inlet valve and reversed the process to assemble washer back together. Total time for repair, about 45 minutes. I now have full running cold water to washer. Thanks guys for the video you provided. Would purchase again if needed. Thanks again!!! Water Inlet Valve with Mounting Bracket Part Number: PS334646

Removed two clips on back panel holding control panel.Removed end plates on control panel. removed two front screws holding control panel. removed wiring harnesses noting location. Set control panel aside. Removed two large clips holding rear panel to washer cabinet. Pulled washer cabinet from the front away from the rear panel and tube. Removed two screws holding water inlet valve. Removed water inlet hose from inlet valve using channel lock pliers. Installed new water inlet valve using supplied mounting bracket. Reassembled washer in reverse order.

Unfortunately after i replaced the new switch the drier worked well. After it stopped for the 2nd time we wanted to put a load and start the swit lost contact. It was not working.It lost the contact with the circuit. No clicking sound the drier not functional. I guess need a new switch?

Turn off water, unplug machine
Disconnect water lines to the valve
Unscrewed the clear plastic tabs on the top of the machine, then pryed the back away from the top white part.
Two gold clips can be popped out with a long flat head screw driver.
Pulled the back away from the machine enough to disconnect the wires from the valve. Unscrew the screw(s) from the valves.
Old valves out, new valves in. Plug in the wires, screw in the screws.
Then, to get the gold tabs back in place.....i called NASA.
just kidding. They're tough!
I slipped one into the back and held it in place with my thumb. Then I lined the piece up with the slot inside the machine. Then, i pryed the top white part away as I pushed them together. Stuck a long handle screwdriver down in and pushed REALLY hard on the gold tab to get it to snap into place. Everything is really tight, so you might have to try it a few times.....i left some blood behind.
repeat for the other side, snap in the clear tabs, hook up the water lines, plugged it in......
Then I sat back and listened to my wife praise me for fixing her machine!

I got a few hints from YouTube (how to remove the washing machine casing) and rest was very simple

received valve as ordered a simple installation. everything went well.home owner can do this repair

1- Remove power connection, remove water connections. 2- Remove the top controller box and free it from its hinges. 3- Loosen the back cover to get access to water valve assembly. 4- Remove hose clamp connected to inlet water valve. 5- Remove the old water valve which is secured with 1/4" screw. 5- For installation perform step 5 to 1 and then test your Installation.

We got the parts, watched your video a couple of times and then began the repair. It went well with one exception. None of my socket extensions were long enough to work well. The required length might be added to the video and the printed installation instructions. Also it would have nice to have been able to order a small tube of the recommended lubricant. Overall I was very pleased. Jack