Models
>
11074410100
11074410100 Kenmore Washer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
There are many symptoms that may indicate an issue with your water inlet valve. These can include your washer not filling with water, it will not stop filling, the washer is leaking, or it is both fil...
In Stock
$23.69
This 3 prong lid switch is used for washing machines that do not have a tub light.
In Stock
$5.76
Also known as Main Outer Tub Seal. This part helps to prevent leaking from the bottom of the tub.
In Stock
$11.80
This hose clamp extends from half an inch to an inch in diameter. It is made entirely of metal and is intended for use with Maytag brand washing machines.
In Stock
In Stock
In Stock
In Stock
In Stock
In Stock
$9.81
Note: This part has been updated by the manufacturer. It may appear different but will still function the same as the original.
Special Order
In Stock
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for 11074410100
Viewing 7 of 7Leaking
Fixed by these parts
How to fix it
No hot or cold water
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Will not drain
Fixed by these parts
How to fix it
Will not agitate
Fixed by these parts
How to fix it
Water Filling Issues
Fixed by these parts
How to fix it
Won’t Start
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Roy from Nash, TX
- Parts Used:
- 285805
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
washing machine is slow to fill with cold water
My washing machine became slower and slower to fill over the past several months. It also made a loud squeeling noise during fill-up (all this was on the cold water side only). I removed the old water inlet valve and tore it down, expecting to find corrosion or trash that was blocking the valve from opening completely. Turned out to th
... Read more
at the rubber diaphragm / seal was permanently "kinked", making it difficult to open the valve. The hot water seal was fine, but to make sure, I swapped them and re-assembled the washer. Now the problem was with the hot water, confirming what I thought. I ordered a new water inlet valve on Monday night and received it Wednesday! Installed it within 30 minutes and it works perfectly now. I am very pleased with PartSelect.com. I will definitely be a repeat customer, but hopefully it won't be anytime soon. ;)
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wendy from Dunlap, CA
- Parts Used:
- 285805
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Cold Water would not shut-off
To discover what the problem was, I intially tested the inlet valve by blowing into both sides - discovering that the cold side was stuck in the open position. The hardest part was removing the back of the machine. First, you unscrew the top plastic part which contains the controllers by phillips head on either side. Then you pop the c
... Read more
lips out with a large slot screwdriver, then at the bottom, a nutdriver or large slot screwdriver there are two nuts to remove. The valve itself took a small nutdriver and pliers to remove the hose. Took less than 20 mintues to complete repair. Washing works like new now.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clay from Laramie, WY
- Parts Used:
- 285805
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench set
The washer would not stop filling.
I took everything apart and put in the new inlet valve. Tried to run the washer and it was still not stopping when filling. I looked more into it and the tube that comes up from the wash basin to the load size selector switch was disconnected and that was the real problem. If this happens to you, I suggest first looking under the contr
... Read more
ol panel at the clear tube and ensuring that it is connected to the switch. Then if that is connected it is probably the inlet valve. There are helpful installation videos that can be found on the part select website that I would recommend looking at before taking things apart because it will make it much easier.
Read less
Was this instruction helpful to you?
Thank you for voting!