11020097993 Kenmore Washer - Instructions

I loosened two screws which held the knob panel in place. I undid the two clips holding the cabinet and removed it. The pump has two clips holding it on, I removed those and the pump came free. Taking advice from these forums, I did not remove the hoses attached. I disconnected the wiring harnesses from the motor. The motor has 2 clips also, these being held on with screws. I removed the screws and the clips. THE MOTOR IS HEAVY.
You will see the coupling on the "spindle" of the motor. In my case, both plastic pieces were cracked in 2 places. I removed the old coupling and cleaned the "spindles" and lightly regreased.
The replacement pieces I ordered were the "improved" ones with the metal insert. They were a tight fit on the motor but I used a socket and hammer. (lightly). Line up the coupling pieces, reattach clips, DONT FORGET THOSE SCREWS HOLDING THE MOTOR CLIPS. Pump goes on next, etc. MAKE SURE ALL WIRING IS RECONNECTED! Cabinet goes back on, large clips holding cabinet to rear of machine go back on. Knob console flipped down and reattached.
Plugged it in and I was good to go! This washer is almost ten years old and this is the second time I have been able to bring it back from the dead, the first time being the agitator "dogs" wearing out. THANKS PARTSELECT!

I followed the online instructions and found it remarkably easy. I saved a lot of money and will certainly use PartSelect in the future! Washer works like new again!

I had given up on repairing the machine and placed order for a $650 washer. After returning to home from this shoping, I wanted to know possible problems with the current machine and came across a story on your web site attached to the Coupling parts description. It described the repair details. Encouraged I placed order for this $15 parts and repaired in an hour, saved the replacement machine cost. Thanks a lot

We had to take the motor out and remove the coupling, when putting it back together we had some problems because the washer was on its side and the lid was open. After putting the motor and coupling back together we tried to turn it on, unknowing to us the lid was open so nothing would happen, finally we realized the lid was open. The actual repair was not complicated, just human error made it seem than way

removed water lines from back of washer. tilted washer to get access to the pump/ removed 2 hoses at pump and removed to snap clips attaching the pump. easiest repair i ever did. washer works fine now.

slid the old seal off the lid and the new one popped on so easily
I do so many self- repairs at home now this was not even an issue.

Started taking machine apart, would of been easier if I had looked at the online diagrams first, but dismantled enough to find a few broken parts, I could not tell the coupling was broke till I actually removed the water pump and motor. Total cost for 3 plastic parts was less than $25 including shipping. Received parts in 3 days on standard lowest cost shipping. Put machine back together, with just a few extra screws and wire clips, but machine works like new now. Much better than the cost of new or used washer.

I popped the dispenser cap off, pulled off the plastic cover that sits on top of the agitator directional cogs assembly, and used a socket wrench with 2 extensions on it to unscrew the nut holding the assembly in place. I misplaced my socket screwdriver and rather than try to buy a nutdriver that matched the size, I just bought a little 3/8" socket extension kit (I needed about 8" of length to be able to use a normal socket wrench). My hands are pretty big so I just had to use pliers to pull the agitator cogs assembly out. Next I just turned the assembly upside down, slipped the plastic ring off that holds the cogs in place, and put the new cogs in place of the old ones. Reassembly was just as easy. The job took about 15 minutes, and once everything was back together the agitator worked like it was brand new.

First, disconnect from power & turning off the water. Then, accessed the part by tipping the unit back enough to work. Remove the hoses by loosening the spring clamps. Here is where things got a bit sticky. The pump motor shaft had corroded enough to make removal of the pump a wrestling match of sub-WWF levels. Once forced off, additional time was spent removing corrosion from the shaft to facilitate fitting the new unit. A little lube was used here. Re-assembly was quick & washer was righted, plugged in and returned to service. It is a simple repair which can, with a little acting ability, be portrayed as a monumental task requiring super-human strength & the wisdom of Solomon. I played the part well enough to merit a huckleberry pie for my effort & sacrifice! Thanks!

Unpluged washer. Turned washer on its side, unpluged wire harness to motor. Removed hoses to pump on motor, removed screws and nuts holding motor, then pulled out motor. Popped off old couplings,intalled new, reassembled. Piece of cake!

It took me awhile to figure out how to get the shell off the washer frame. (I didn't know about flipping it on its back). Once the moving parts were revealed, the water pump was staring at me with both ports. I turned the machine on and saw that the leak was coming from the pump.
1. Cut power
2. unclipped pump with pry with screwdriver
3. detatched both hoses - flood ensued
4. gently pulled pump off transmission
5. replaced pump

I reccommend doing this repair with empty tub.

Very easy and cheap repair. Hardest part was getting cabinet back on. Watched u tube video before and easy and quick to do take off cabinet, in clip motor and slide new motor coupler in. Put back together

It was a miracle. We were going to get rid of the washing machine because it made so much noise and rattled the whole house. It also 'walked' across the room with every load.
I simply replaced the wear pads (2 of them were already worn away), and now it is as quiet as when it was new. AMAZING!

I followed the instructions in the video on the part page (part #PS11741239), which was also conveniently linked in the item shipped email. The replacement of the part was very easy ... the hard part was balancing the washer again (kitchen floor seems to have sunk in the middle). Back to normal function without having to suffer a flood first. Thanks.

Thank you for asking me how it went. the washer would not spin or pump water out, so I put it on its side and saw that the coupling was bad.
so I found you on the internet, thankyou very much, and put a order in for the part. well waiting for the part, I took the old coupling out it was easy, there was two metal bands one on each side of the motor took them off two bolts holding a plate on, and had old coupling in hand. and it was easy to put back with the new coupling. I enjoyed working on it. Dennis