11027086605 Kenmore Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Joaquin from Santa Clarita, CA
- Parts Used:
- W10820048
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Washing machine was rocking a lot, and stoping too much.
Our washer wasn't really working, we called a tech to diagnose our problem, he charged us $35 to let us know that we had a suspension problem, he promised to call us back next day with the estimate for the repair, he never did. So I decide to search, I found a video showing exactly how to do it, it was a very easy, and simple process that I decide to order the parts my self. The parts were delivered to my door in 24hrs. I installed the parts in less than 45 min, and now our washer is working like new again!!!
Thanks guys.
Thanks guys.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Gore, OK
- Parts Used:
- W10820048
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
washer kept going out of balance
Removed cover and removed rods,replacing them one at a time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jacob from Glennville, GA
- Parts Used:
- W10536347
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
washer would not drain water
need to get washer turned on side where you can work underneath the machine. This job is alot easy if you get where you can see good and have plenty of room to work. You have to unhoook the wire from the old pump and then take the two mounting screws off from there you unhook each hose by squeezing clamp together and sliding backwards away from pump. A pair of needle nose pliers can make this process easier if the clamps are turned in an hard to get to position. You mount the new pump the same way as taking off the damaged pump. Take a screwdriver to help you slide the clamps up onto the new pump makeing sure the sleeves are completely over the new pump fittings and the clamps are slid up evenly, so you want have any leaks. Then replaces wiring harness and mounting screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- richard from asheville, NC
- Parts Used:
- W10536347
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
replaced leaking pump
Easy repair. Went to You Tube and saw PartSelect video. The best instructions...should make a link from parts page to video of install. Also replaced Heat element on Dryer. Watched video first.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JESUS from PORT ARTHUR, TX
- Parts Used:
- WPW10619844
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
did not work
reemplace the lid lock assembly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janelle from Gray, ME
- Parts Used:
- W10536347
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
water leak at pump, crack in pump housing
First off always remember to empty all pockets, coins etc ruin pumps.shut off water supply, unhooked water lines and drain into pan.tilted machine forward so i could work on pump which is located lower left. drain pan under pump area, removed 2 rubber water hose's 3 5/16 screws with nut driver. Very carefully un clip rear of housing and removed wire harness. installed new pump
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elijah from Point Hope, AK
- Parts Used:
- W10193886
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set, Wrench (Adjustable)
UL flashes, will not spin, really loud,& black spots under washer
We ordered the outer tub & bearing and now the washer works like it was brand new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from germantown, TN
- Parts Used:
- WPW10189966
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
washer wouldn't go in the spin cycle-
Pulled washer from back of wall and disconnected power source. I removed three screws in back that houses the ol motor control board. Also, I had to pull the front control knob off so that I could lift the cover to expose control board. I took several pictures of the motor control board before unplugging the wires just in case I forgot where the wires needed to go. Very simple process and had machine working within 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kelly from Petersburg, WV
- Parts Used:
- WPW10619844
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
My lid lock assembly was bad and therefore the washer lid would not lock to allow for washing.
Went to youtube.com and watched the video that took you step by step in replacing the lid lock assembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Ormand Beach, FL
- Parts Used:
- W10193886
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
noisy
Removed old tub assembly and installed new tub. Job took a little longer due to first new tub arrived damaged and I had to partially reassemble machine temporarily until second tub arrived.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Delinda M from Chicago, IL
- Parts Used:
- WPW10189966
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
f1, code on the face plate of the washer,we kept on resetting it
we ordered a motor controller,pop out the old one,then replaced it with the one we ordered,and bingo,problem is solved
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MEECHE from LANCASTER, SC
- Parts Used:
- W10536347
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
noisey water discharge pump
PLASTIC motor housing gets hot and become loose. causing bearing to spin and make noise . Replaced motor that was quick and simple by removing 3 screws and 2 hose clamps , pluged up motor and begain washing again with no problem . Just wish motor housing was not plastic .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bonnie from Baytown, TX
- Parts Used:
- WPW10189966
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Every wash cycle would throw out the "F1" code and I would have to keep changing the wash cycles until one would finally catch. Replaced Motor Control Board and now works excellent!
Read the previous reviews and showed my son the diagram which he then replaced the part in about 15 minutes. No more hassle and works like a charm :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- brett from seymour, IN
- Parts Used:
- W10820048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
replace suspension rods
took top off.2.replaced rods one at a time.placed top back on.very simple.evan got new bushings for the top.very simple process.no skills required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- axel from lighthouse point, FL
- Parts Used:
- W10820048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
drum made loud noise
put machine on side pushed old rods out to top installed new ones. runs like new. tried to ask mechanics or stores nobody would help with info, they all want to send mechanics with 80$ just to get here. it was easy to do. thanks
Was this instruction helpful to you?
Thank you for voting!