11045091404 Kenmore Washer - Instructions

Remove three screws on bottom panel lift up and remove panel.The water pump in right in front. One screw holds it in place and the input and output hoses are on the back side.The hose clamps are a little hard to take off I found that before taking the one screw off the pump remove these two lines.Putting the pump back in secure the pump with the one screw. The output line is easy the intake line can be a bit of a more work to get it on because the rubber is so thin.Getting this hose and clamp was tough. Most of all use a wet vac to remove water in washer and vac out the line to drain doing this will be water free during replacing water pump.Run a cycle to make sure the lins do not leak. The other is the people that has posted this replacement are very good

Had the old pump out - 1 screw and two hose clamp to unhook and an electrical wire to pull out - couldnt been any easier - when new one came took 5 mins to install - did a load to make sure pump worked before put it all back together

Factory hose clamps were awkward to maneuver. I used automotive radiator hose clamps instead. They worked great.

I followed your repair video explicitly, simple fix. However, one should
be careful when disconnecting the two prong electrical connector from
the heat sensor. the two black wires can pull free easily. In that case, the
rear of the female plastic wired connector must be extracted to allow the two black wires to be "pushed" into the narrow slot which displaces the
wire insulation and allows for a good electrical connection. If a punch tool is not available a pair of needle nose pliers works. Also, observe
the orientation slots on both the male andfemale connectors - they
connect one way only! I set the washer on it's face while effecting this
repair to better see what I was doing (eyesight not as good as it used to be). Thanks for the timely support!

Water was slowly filling the wash tub and spilling out front of machine. Cause was the water inlet valve solenoid was not fully closing.

Turn off water to the machine
Unplug machine
Pull machine away from the wall
Remove the water inlet hoses.
At the back-top of the machine remove the three screws holding the top on.
Lift up top from the rear and remove it.
Disconnect the hose connected to the water inlet valve.
On the outside of the back panel remove the screw holding the water inlet valve.
Remove the water inlet valve.
Reverse the process to install the new valve

NOTE: in my case the hold in the back panel did not line up with the hole in the new water inlet valve. I drilled another hole.

Removed the outer spring with pliers. Pushed the bellow into the drum. Loosened the clamp on the bellow with a stub nose screwdriver. Removed the bellow. lined bellow up with soap fiting. Reversed procedure to reinstall.

As easy as 123 two torx screws removed old pieces and install the new one and like that ready for another 15 years.

First I removed the retainer ring that holds the outside bellows on the frame of the front washer.
I then pushed the bellows inside of the drum of the washing machine in-order to get to the clamp that holds the bellows on the inside of the drum. To pull the clump I had to use a stubby screwdriver and socket drive to loosen the clamp. Once the clamp is loosen I was able to pull the bellows off, of the drum and out of the washing machine. Installation was the reverse of removal.

2 clamps and its off, problem is if you have average size hands you will struggle in getting the back clamp on and off.

Shocks are the #1 recommendation for this problem, but they were not the solution. The problem turned out to be broken weld in the stainless tub. Three of the shocks can be replaced from the front, the one under the motor can only be accessed from the back of the machine, which means it has to be pulled out away from the wall. Taking the old ones out is kind of a pain, they don't twist off easily and there is little room to use tool. Putting the new ones in is easy, they just twist into place.

easy process: troubleshoot problem on website-- order part--get part--watch "how to replace"video on you tube-- get it done with only a screwdriver--go out for movie and dinner with $$ saved.

Removed covers per instruction video provided by website

We do not wish to have our repair published. The part itself was perfect and corrected our leaking problem but we did have difficulty with the installation despite detailed instructions. We appreciate a good price for the perfect part!

disconect wayer inlet hoses.remove screws that hold the top cover. This will expose the water inlet valve. remove the defective valve and any other associated clamps,hose etc. test run for leaks.

Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.