11047799701 Kenmore Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Carl from Patterson, CA
- Parts Used:
- WP8182233
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
baffle in tub fasteners broke, baffle disconnected from tub
This part slides in and snaps in place, a 15 second job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew from ROCKVILLE, MD
- Parts Used:
- WP8183270
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Washer would not start reliably.
Followed the video on the website. Very easy to replace the part and it fixed the problem. The trickiest part was reinstalling the ring that holds the rubber gasket in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from Branford, CT
- Parts Used:
- 280187
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Clothes came out dripping wet
Just removed the bottom cover to access the water pump. Drained the water through the filter housing. One screw and two hose clamps and the pump was out. Installed new pump and checked for leaks. None found so the cover was secured in plase. Great news, WIFE is happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MIKE from BENBROOK, TX
- Parts Used:
- WP8182233
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Baffle in washer tub broke off
Snaped new one in place and done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Valerie from Huxley, IA
- Parts Used:
- WP8182119
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Leaked water
simple repair. After reading other reviews my husband was confident he too could do the repair. He was right, we were so very glad not to have had to call for service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ramon from Houston, TX
- Parts Used:
- WP8182119
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Front seal leaked
It was so easy my wife replaced the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from Adrian, MI
- Parts Used:
- 280187
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
Shaft in water pump broke
I removed the one screw that holds pun
mp in place. I pulled to the left and foward about an inch to remove hoses and unplug wire. then pulled pump assembly out. The new one went right in. The wire plug went right in without any customizing. I think this was about as easy as it gets.
mp in place. I pulled to the left and foward about an inch to remove hoses and unplug wire. then pulled pump assembly out. The new one went right in. The wire plug went right in without any customizing. I think this was about as easy as it gets.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Virginia Beach, VA
- Parts Used:
- 280187
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Washer would not drain.
Removed three screws holding the cover, then one screw holding the pump assembly in place. After unplugging the power, it took two minutes to remove the clamp-rings from the hoses. The reverse was equally idiot-proof! But THIS "idiot" had 10-thumbs which added to the time to replace the lock rings! Added an extra 5 minutes at most! _grin_
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jill from New Rochelle, NY
- Parts Used:
- 280187
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The water didn't drain, so the drum wouldn't spin
I took off the cover, removed one screw. Removed two hoses and the electrical connector. It only 5 minutes to replace the old pump with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nathan from Cincinnati, OH
- Parts Used:
- WPW10415587
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
f35 error code
removed 3 screws from back, then pulled hose of piece and disconnected wire clip. reassembled. have tu turn bottom of the piece torward you to remove from machine. this part is located on the back right side, black on my machine 1x2x2/4 inches in size, this is looking down into the wash machine from the front.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from BODFISH, CA
- Parts Used:
- WPW10415587
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Suds and F35 error
Starting getting these errors...but we had also been washing about 300 towels a week from our gym for about 3 months. I contacted an ex-sears repairman friend of ours for advise. He first recommended checking the pump filter basket. It was easy to get to by taking off the front panel. It did have about three hand wipes and other debris in it. Removing these items did cause the errors to occur less often, but they still did continue. We had our repair friend come over and go through the diagnostics checks as per the instruction sheet that was on the inside of the washer. It came down to being the pressure sensor. After replacing the sensor, the washer has worked flawlessly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GARY from CLARKSVILLE, IN
- Parts Used:
- WPW10110225
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
F-20 Error Code
Take off top of washer and the flowmeter is in the back lefthand corner on the top of the washer. Replaced the water level switch on the top righthand of the machine also. Got about 150. 00 Total invested w/service call from local tech. F-20 has not came back yet. I hoped it fixed it washer is only 3 yrs. Old. -Gd
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- wilfredo vega from STRATFORD, CT
- Parts Used:
- W10822553
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable)
Drum was out of balance
Easy fix,
I remove the front lower panel and the shocks where right in front of you , with a little twist with an adjustable wrench the cam right off . I removed and the replaced and it the same when you remove the back panel.
P.S when installing the shocks start by connecting to the bottom and then connect to the drum it will make it lot easier.
Good luck on your repair
I remove the front lower panel and the shocks where right in front of you , with a little twist with an adjustable wrench the cam right off . I removed and the replaced and it the same when you remove the back panel.
P.S when installing the shocks start by connecting to the bottom and then connect to the drum it will make it lot easier.
Good luck on your repair
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- richard from chetek, WI
- Parts Used:
- WP8182233
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
baffle connectors worn off
Placed baffle inside of washer and pulled to lock into place. EASY!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gustavo from YOUNGSTOWN, OH
- Parts Used:
- WP8183202
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Door was not closing properly, broken swivel arm under hinge.
removed door from washer, set flat on table and just loosen up the screws all around, removed old hinge and replaced with new hinge, very easy. back to washing clothes.
Was this instruction helpful to you?
Thank you for voting!