11028042701 Kenmore Washer - Instructions

We ordered the outer tub & bearing and now the washer works like it was brand new.

Tilt the machine over to access the bottom I rested it on a dolly.remove the rotor with an allen wrench .then rmove the 4 bolts on the stator .then lift it off the main shaft and unlug the sensor wires . just reverse the process to install the new one (be sure to allign the arrows on the sensor and the stator when reistalling. I wish i could say this solved my problem .my machine runs untill the spin cycle then it starts shaking and gives the uneven load alarm again.

we ordered a motor controller,pop out the old one,then replaced it with the one we ordered,and bingo,problem is solved

reemplace the lid lock assembly

I read the directions on this web site and was able to install the new drainage pump in about 30 minutes. I suprised myself. Thanks.

Our washer wasn't really working, we called a tech to diagnose our problem, he charged us $35 to let us know that we had a suspension problem, he promised to call us back next day with the estimate for the repair, he never did. So I decide to search, I found a video showing exactly how to do it, it was a very easy, and simple process that I decide to order the parts my self. The parts were delivered to my door in 24hrs. I installed the parts in less than 45 min, and now our washer is working like new again!!!

Thanks guys.

To start out, I ordered two parts for a washer, a water valve and a recirculation pump. I found out that one of the solenoid switches went bad on the valve body. I tried to find just this switch but found out that you have to buy the whole valve assembly just to get one of the switches. The recirculation pump was making a really bad noise when it would run. The problem with the pump, the impeller that pushes the water out of the pump was in pieces in the pump head housing. I paid to rush the delivery so the washer was not unusable for every long. The parts showed up as planned with one problem. One of the solenoid switches was not attached to the valve body, it was broken off of the valve body. I called the service number that was on the packing slip. The lady I spoke with about the broken part apologized and quickly placed another order with the same part. Down side was she could not get it sent out that day because it was late afternoon on a Friday and the shipping department was closed. So the earliest I would receive the part would be the following Tuesday. She did refund my rush delivery cost, so i paid for just standard delivery. I had the recirculation pump on the Friday I was hoping for but still could not get the washer running until I received the water valve the following Tuesday. I told the lady I understand her hands are tied about shipping the part out that day, Since there was nobody there to ship it. I also understand that sometimes things do get broke in transit. The part was delivered on the following Tuesday as promised. I opened up the package to inspect it. This time the part inside the package was packed a little different and a little more secure. I was glad the service department was easy to deal with, very respectful and willing to correct the problem. All and All The repair went really well, had no problems installing the parts what so ever. (To make things a little easier to remember where they go)Leave the old wire harness intact with the old water valve when you remove it. Once the new water valve is install you can reference how to install the new wire harness from the old water valve. The pump had 3 screws and 2 hose clamps to remove it. It is easier if you can tilt the washer forward (just a little) to change out the pump. You can change out the pump without tilting the washer, just easier if tilted. I would order from partSelect again. I would recommend my friends and family to order from partSelect.

At the time that I received the order part, Me and my Wife and 15 years old Douther got on it. We removed the very top of the counter and replaced once at the time every supension rod cleaned nice and neat. then we put the top on it's place conected the water hoses pluged it in and it was ready to roll.

Removed the fabric softner at the top of the agitator (needed a screw driver to pry it loose) and reached in to grab the barrier with my hand and pulled it out, very simple to do.When I put the new one in I put some liquid soap on the gasket and it snapped right into place.Very easy to do, all is well now, thanks Part Select.

need to get washer turned on side where you can work underneath the machine. This job is alot easy if you get where you can see good and have plenty of room to work. You have to unhoook the wire from the old pump and then take the two mounting screws off from there you unhook each hose by squeezing clamp together and sliding backwards away from pump. A pair of needle nose pliers can make this process easier if the clamps are turned in an hard to get to position. You mount the new pump the same way as taking off the damaged pump. Take a screwdriver to help you slide the clamps up onto the new pump makeing sure the sleeves are completely over the new pump fittings and the clamps are slid up evenly, so you want have any leaks. Then replaces wiring harness and mounting screws.

Easy repair. Went to You Tube and saw PartSelect video. The best instructions...should make a link from parts page to video of install. Also replaced Heat element on Dryer. Watched video first.

Rubber O ring around the Inner Cap was rotted and busted through. Replaced with new Inner Cap Seal. Easy as pie!

Pulled washer from back of wall and disconnected power source. I removed three screws in back that houses the ol motor control board. Also, I had to pull the front control knob off so that I could lift the cover to expose control board. I took several pictures of the motor control board before unplugging the wires just in case I forgot where the wires needed to go. Very simple process and had machine working within 15 minutes.

I removed the screws from old hinge that had broke. The piece came right out with ease. I slid the new hinge in to the hole that it went in. No struggles with ease. Lined up the screw holes and put the screws back in. Finished! Works like a charm.

Just had to remove cap on agitator and replace new rubber seal.