11016964501 Kenmore Washer - Instructions

1. Unplug washer 2.turn off water, remove hoses from washer.3. Remove back cover, Remove screw holding inlet valve, carefully remove modular wiring, noting which wire goes where. Discard old inlet valve. Install new part. Reverse the above directions for installation.

Removed the old hoses and screwed on the new hoses.

Followed the video posted on the website. Everything went great - first repair attempt took about 45 minutes. Time consumed mostly due to the straps that hold the motor in place being very difficult to put back on and that the cabinet was a little difficult to replace due to the amount of rust around the bottom of it. Tried out the washer when done, and noticed a burning rubber smell. Took everything apart again, checked it, and everything seemed to be ok (made sure all four rubber feet were in place on the motor) so put it all back together again. Noticed the smell again so took it apart a third time, and when the motor felt pretty warm, decided to do an internet search for "burning rubber smell after replacing drive motor coupling." The answer popped right up - the replacement parts were not solid plastic like the original ones- they had metal on the inside of them, and needed to be tapped, a bit forcefully, with a hammer and socket until flush on the both the motor and transmission axles. Once the parts were flush, the straps that hold the motor in place snapped right on. Still a challenge with the rusted cabinet, but once all together again, worked perfect! Thanks to this site , I have fixed washers, dryers, and refrigerators and used them now nearly 20 years! I showed my daughter and granddaughter how to repair them and they don't hesitate to pitch in and help or handle the repairs on their own - again with much appreciation to this sitefor the accurate "how to" videos, the right parts, fast shipping, and great prices.

First used wet vac to get water out. Unplug electrical cord. Shut off water and unhook lines. Unhook drain tube. Flip over on side. Take belt cover off. two screws.
Took photos of parts removing just for re- install. Ordered parts from part select.com. Came in Two days. The dealer was on 12 days I gave up on them. I removed actuator two easy screws and pulled off electrical connection no tool needed. Then removed pump three longer screws Than other part. Make sure to label them in a ziplock baggie. Plus I removed hose clamp with pliers slide Back on hose and pull hose off. Then remove electrical connection on pump. If it makes you feel better label each with masking tape so I know where each connection goes. Then replace pump first with new one. Make sure you push it in hard then the screws. Don’t over tighten. Plastic parts break. Hook back up hose slide clamp back over fitting end with pliers. Hook up wire connector. Next hook up actuator. Two screws wire connector and your done. Put belt guard back on. Socks can get caught under washer get in belt and cause major issue. Then you need to reconnect water lines. Make sure hot goes to hot. Cold to cold. Drain hose hook back up. Plug in power cord. Now the fun part. Run a diagnostic and then calibration. See you tube videos it’s like 3 clicks to left then two to right with selector knob. Write down the exact amount of clicks and steps. It works. Be sure to turn knob 4 times to left to clear it like a combination lock. Don’t let the noises scare you it makes all
Kinds of sounds while calibration goes on.

As with any repair job, the hardest part is getting started and figuring out how to take it apart. I first tried to remove the top, by prying up on it,( his has worked in the past). This only broke the plastic retaining clips. I then removed the two plastic covers on each end of the control panel, then the two screws that hold the front of the control panel down. and lastly slid the control panel forward and out of its slots. I then used a 5/16th nutdriver to remove the four screws from the back panel. Now I was able to pull the panel back away from the washer body enough to use needle nose pliers to to remove the four electrical plugs located on the mixing valve. I used a felt tip marker to identify the locations of each plug. I used a 1/4 nut driver to remove the one mounting screw that held the valve in place and removed the valve. When the new valve arrived, It took about 15 minutes to re-install the valve and put everything back together.

I did a Google search for the model number and found this site, PartSelect.com. Based on the diagrams on the site and what I could see underneath the washer, it was clear that the motor coupling was now gone and the shattered pieces of it were all over the floor. So I ordered a new coupling and waited for it to arrive, it was shipped in just a few days. Once I had the new coupling all I had to do was remove a couple of brackets holding the pump onto the motor, and the motor onto the gearbox; unplug the electrical terminals and lift the motor out. There are two halves to the coupling, one sits on the shaft of the gearbox and the other on the shaft of the motor. Both of these are seated into a rubber boot that is also a part of the coupling. Once the motor is sitting on the gearbox with all the coupling parts seated in place, just plug everything back in and replace the brackets. You will need a 1/4 socket to remove/replace the motor brackets. Also, it should be noted that you will want to unhook everything that is hooked to the wall (hoses, power cord) but it assumed you've already done this if you have access the the underneath of the washer.

Put new one on work good, but now can't pump no more .the problem now is the spin cycal broke and I not going to fix it. Thank for the part work good.

I watch the video... that simple!

Disassembled top control console and surrounding sheet metal cabinet per the video from this site. i then used a screw driver to carefully pry up each wear pad location individually and inserted the wood wedge. to about 1 1/2 inch height. rwmoved the old wear pads and popped in the new pads one by one. Closed up the unit and tested the machine . It ran like new. No more noise or viberation

First I screamed at the ceiling, because I have a three year old and an infant, and the washing machine was dead. Then I went to youtube. It seemed like the "agitator dogs" were the issue.

In this spirit of any repair, I replaced them, and it was not the issue. I don't know what I expected.

Ceiling. YouTube. Pacing.

Then I figured it was this part - the motor coupling. I unplugged the machine and took out the drain tube. I leaned the machine back and propped it up with an empty detergent bottle, because those were abundant. Ratchet off a few bolts and the motor comes out. The coupling was indeed broken. The new one slips right in - I tapped it a few times with a mallet for good measure / vengeance. Ratcheted the bolts back on and tipped it back up.

Pros: Washer works now.
Cons: Everest-esque laundry pile to address.

But hey, it worked! I am no handyman and it wasn't too bad at all. Half hour tops.

Found leveling spring loose on bottom of washer, the sheet metal on bottom of cabinet ad rusted through. Drilled new hole in sheet metal and installed new leveling spring. Greased hole with blue marine grease so it will last another 40 years.

Disconneted hoses,unplugged.removed drain hose.Turned unit on its side.Unsnapped retainers,tryed to to pull off with just my hands,that didn't work.Used a pry bar to pop off.The end of the shaft was rusted out.I took a dremel with wire brush and cleaned up the end.Then the pump njust slid on.I took it off again and applied some anti-sieze on the end of shaft.then put pump back on.Snapped the retainers and put hoses back on.It was easy.When I first looked up washer parts,I found this other site and the price ws doulbe.Then I found you guys ,1/2 the cost and it was here in 2 days.Thank You Parts select.

We had to take the motor out and remove the coupling, when putting it back together we had some problems because the washer was on its side and the lid was open. After putting the motor and coupling back together we tried to turn it on, unknowing to us the lid was open so nothing would happen, finally we realized the lid was open. The actual repair was not complicated, just human error made it seem than way

removed water lines from back of washer. tilted washer to get access to the pump/ removed 2 hoses at pump and removed to snap clips attaching the pump. easiest repair i ever did. washer works fine now.

I had given up on repairing the machine and placed order for a $650 washer. After returning to home from this shoping, I wanted to know possible problems with the current machine and came across a story on your web site attached to the Coupling parts description. It described the repair details. Encouraged I placed order for this $15 parts and repaired in an hour, saved the replacement machine cost. Thanks a lot