11047532602 Kenmore Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Steven from Kalamazoo, MI
- Parts Used:
- WPW10730972
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
The washer was flashing f-21 code. And the cloths were soaked.
First thing, unpluged the washer. I removed the lower front acces panal. I then propped the washer up on 2 pint sized paint cans to reach the pump mounting screws. I disconnected the wire bundle going to the pump. Then removed the inlet and outlet hoses from the pump. Then I removed the 2 mounting screws on bottom and slide the pump to the left and removed. I then pump the new pump on the same way I took the old one off, but in reverse. Easy and fast the worst part was the price of the pump.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Mount. Pocono, PA
- Parts Used:
- WPW10111435, WP8540108
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Leaky bellow/door seal.
I removed the three bottom screws and removed the plate. Removed the control panel, removed the star screw on the left side and pulled off the front panel of the machine. Loosen the bellow clamp with a phillips head and pull off the front spring clamp on the bellow. Pull off the old bellow and re installed the new one. Installed and tightened the bellow clamp and spring loaded clamp on the front of the bellow and re installed the panel, and control panel. Checked for leaks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eddie from El Paso, TX
- Parts Used:
- WPW10111435
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Washer was leaking thru front on washer
I had to replace the bellow to the washer because I discovered the leak was from the door and bellow area, only problem I really had..... was installing the bellow on the outer drum, I applied a coat of hand soap to make it easier to secure in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dalia from Boonsboro, MD
- Parts Used:
- WP8540101
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Belt Broke - Again - 4Th Time In Three Years
Removed top panel. Removed rear panel. Replaced belt. Fairly easy only issue was getting the actual belt pulled enough to wrap around the pulley.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Antonio from La Puente, CA
- Parts Used:
- WPW10730972
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
My washer would not drain, weird noises, etc.
This part worked great! Completely fixed all the problems that I had with my washer. A bit hard to actually place it in(pliers are necessary) but otherwise very easy to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tina from Denver, PA
- Parts Used:
- WPW10730972
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
needed to replace water pump
dryer stacked on top of washer. had to lift washer and block w/2 x 4 to get under unit and replace pump
Was this instruction helpful to you?
Thank you for voting!