11047789701 Kenmore Washer - Instructions

This was so easy to swap the parts out. The plastic hooks that hold the pieces inside our washer had just worn out. We put our washer and dryer through LOTS of use and I am amazed it has hold on this long! The broken piece just popped out and the new piece just snapped right in. Thank you for your speedy shipping and the great price.

The drum baffle came off. This website provided a diagram to make ordering the part easy. It was reasonbly priced and came in the mail very fast. I had it installed in my washer within 5 minutes. Excellent experience. Thank you.

replaced drain pump.Saved 200$

The new piece just took seconds to install. You had to set the piece slightly farther back then where it belongs, and with a slight downward pressure, just slide the part toward yourself until you hear it click into place. About 5 seconds and no tools required.

I unplugged the power and tilted the washer back and removed the kick panel. I then unscrewed the pump trap access and set aside. I used the shop vac to remove the remaing water from the washer to the drain pump, unplugged power to the pump, removed the discharge hose and suction hose. After everything was removed, I removed the pump. Everything I read said to take the pump loose before removing everything, it just worked better for me to take everything loose with the pump secure. Going back together I mounted the new pump, plugged it back in (I did not have to remove anything from the plug to use it on the new pump as the insert indicated), installed the discharge hose and the suction hose. I found it easier to rotate the clamp a bit on the sucttion hose to allow me to use my right hand to depress the clamp to get it back in place. Replaced the kick panel, lowered the washer back in place, plugged it in and ran it through a cycle, worked great.

Unplugged electric cord and turned off water supply. Remove 3 screws @ rear of washer and removed top panel. Removed clamps on hoses and electrical connector to flow meter, removed and replaced with new flow meter. Replaced the top panel, turned on water supply and plugged unit in. Finished in less than 15 minutes. Saved myself several hundred $

Very simple repair. Lined up the baffle tabs with the drum slots. Pushed the tabs into the slots, pulled the drum baffle towards the opening of the wahser until it seated. You will hear aclick.

Very simple repair had to remove door from Washer, loosen the seals so that I could remove the old hinge. Inserted new hinge place the door and hinge on brackets and tightened the screws. I was very pleased with the fast action in getting me my parts, less than 24 hours.Thank You.

Easy peezy!! Next day delivery, as promised for parts that could not be found anywhere else. I placed the baffles in the washer and clicked them in using both hands one by one. I'm petite and weigh about 110 lbs. The total installation time was less than 2 mins. I was given a $200 quote just for installation but, spent less than $100 and installed myself. Thank you!! I will not wait so long and shop around next time. I'm going straight to partsect.com to save time and money. Although I have to buy new clothes now since my washer put holes in all my clothes. But, the problem is finally solved and I am so grateful.

I had replaced the flowmeter, but that didn't solve the problem, so I ordered the hot/cold solenoid fill part. Other than ONE screw that was unique -- the back retaining screws were nut driver screws, the one retaining screw was a torx which, of course, couldn't be seen unless you pulled the washer all the way out. Unscrewed that, unhooked the hose clamp with pliers and worried the hose off, removed the four electrical connections (which were TIGHT) and replaced the part. Turned on the water and was dismayed to get a d/l error code. After some colorful language learned from my drill sergeant 40 years ago, I realized that was "door lock" and closed the door tightly. Ran great and the Mrs. thinks I'm a hero.

Placed baffle in drum over slots pushed down on it and slid it back to lock it in place. You will hear it click.

There are three screws in the back panel at the very top. I unscrewed them with a T25 driver tip and pulled the top panel off the machine, the water level pressure switch was located in the right rear corner of the washer. ( If you are facing the washer) I pulled off the hose and unplugged the old switch, popped the switch out, and snapped the new one in re-attached the plug and hose, put the top panel back on and the three screws back in! All in about fifteen minutes. My washer works like new.

It took less time to repair than it took to get new baffle out of the packing sleeve. Set it in drum and snapped it in place. Took about 5 seconds.

repair was a cake-walk with the video there to help.Thanx

I followed the instructions and it was surprisingly simple. Glad I didn't call the "handy-man" since it was easy to do it myself as a handy-woman!