11047567700 Kenmore Washer - Instructions

First unplug the washer and turn water off..Next take off back of the washer ( I used a socket set). Then underneath the front load tub, take that panel off to get to the pump (there are 3 screws in the front panel). Then get a towel put it underneath the water pump. Next take your pliers and squeeze the tab holding the end of the drain hose where it connects to the pump, Slide the clip up on the pump connection, pull off hose ,make sure your towel is underneath the end of the hose.Next reach your hand through the back of the washer and squeeze the plastic holder w[th your hand to release the hose. Then pull old hose out and replace it the the new hose. Just reverse the steps to put it in..

I basically just followed the directions in the Parts Select video. The only thing that was a little difficult was getting the new belt to feed onto the drum pulley, but after a couple of tries I was able to get it on. I'm glad the video mentioned this might be a little difficult or I might have thought I was doing something wrong.

I thought there were just two screws to do the replacement. However, it is necessary to remove the entire plastic outside cover to accomplish this task. There are several screws on the inside of the door, some attach the door to the hinge. Check your manual to determine witch these are. What I ended up doing was completely removing all screws and the door. reassembling was a bit difficult but I got the job done.

one note, remember which screws came from which holes as they are close in size but a little different.

I followed the video that accompanied the parts order confirmation. The replacement of the two parts, bellows and hose, were pretty straightforward. The job took a little less than an hour with little aggregation.

Removed top and front lower panels remove door panel.Remove ring from boot seal don’t damage seal.Replace hose,reassemble.Job is a lot easier if you purchase tool to re-install door ring seal.Tool is available from several sites on the net.

Replaced drain hose

Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.

This was an easy fix . PartSelect was quick and had all the info I needed to repair my washer. Plus shipping was super fast. Thanks

The removal of the bellows was easy and quick. The instructional video was really good. Only one problem with video. The step of removing the console from washer leaves out that there is a center screw in the center of console. I almost broke the console. It took took a long time in getting bellows on interior area due to tight finger space. Wire gasket fairly easy. The outer gasket after getting door and latch on. Whew! That was a bear. Video looked easy. I finally had to get help to get it on. The reason was that every time I thought I had it, the bellows would roll off will the wire gasket. A screw type as the inner area would make it so much easier. Shipping. Kudos to your company. I was expecting that I would be without washer for a week. I ordered on a Friday and it was here early Monday morning. That was amazing. By the way I did this except the outer wire gasket by myself. I finally had to get "husband" to help with that. Thanks Parts Select! If the need arises that I need another part. You will be my go to company.

Followed the most helpful video.with some system differences. Had quite a bit of fitment challenge with the inner bellow sealing process...finally used dish soap to help 'stretch' the thing on.Works fine now thanks.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

removed retaining ring on front gasket, pulled gasket back, took out door lock latch, unhooked wires, then reversed method to replace.

After getting dress that wife denies closing in door out the repair wasant to hard. There are 3 or 4 phillips screws in back that holds top on that have to be taken out and the kick plate cover on bottom just snaps off but the rest is covered very well by other discriptions.(by the way the dress had to be thrown away so not only did i get to by bellow but a new dress also and the bellow was cheaper)

First, I watched the video again just to make sure I had a firm grasp of the task ahead. I gathered up the tools and proceeded to begin. First obstacle: getting the washer tilted back enough to put the blocks under the front feet. The washer was sitting inside a square water pan with a drain connected directly under the middle of the washer. Therefore, the water pan did not move and I could only get the washer moved out far enough to 'barely' put the blocks underneath. Second obstacle: a clump of hair had gathered at the bottom portion of the door unnoticed and caused a slow leak from the bellows. This leak dripped down and rusted out two of the three screws. I had to use a socket set to get the screws out. Third obstacle: getting the pump removed from the bottom of the washer. With the drip, the pump had stuck to the bottom of the washer. Trying hard not to get cut on the sheet metal bottom, I pushed and pushed and pulled until finally the pump let loose. From that point on..smooth sailing just like the video. Washer fixed!

I had to replace the bellow to the washer because I discovered the leak was from the door and bellow area, only problem I really had..... was installing the bellow on the outer drum, I applied a coat of hand soap to make it easier to secure in place.