11026012010 Kenmore Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Delmar from EAST TROY, WI
- Parts Used:
- W11244231
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
replaced drain hose that was missing
slipped the new drain hose on and with locking plyers slipped the wire clap in place after three trys
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from RICHMOND, IN
- Parts Used:
- W10780048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Shaking extreme
Per instruction sent with purchase
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from HANCOCK, MD
- Parts Used:
- WPW10006384
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
washer wasn't spinning after rinsing but the motor was running
I had taken the time to watch videos of this repair so when the switch arrived I knew what I had to do. Removing the screws to get the back cover off was simple as was installing the switch. No tricks here just watch the videos and your all set to do the job
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from NAPLES, FL
- Parts Used:
- W10780048
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
I followed the video guide, which was excellent
I followed the instructions, however I did not have a spot to hold the bar temporarily, so I drilled a hole in the corner frame to hook them in at the front of the machine. All else was easy and according to the video.
Machine works great now.
Machine works great now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ernestine from CARRIERE, MS
- Parts Used:
- W10780048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Making noise when spinning tub hit side of washer.
Remove top of washer suspension
Rod goes on side of tub .
Rod goes on side of tub .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from LANDENBERG, PA
- Parts Used:
- W10780051
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Rock and roll on spin
Replaced the suspension rods.
Must be done on its side as the rods only pull down. There is no slot.
Must be done on its side as the rods only pull down. There is no slot.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from BAKER, FL
- Parts Used:
- WPW10006384, W10721967
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Loose pulley
Tightened up the pulley as the video showed me that might be the issue.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chet from CLEARWATER, FL
- Parts Used:
- WPW10006384, W10721967
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
heavy loads did not spin dry properly
I followed the instructions provided by the video which I thought were spot on. Even to the size of the phillips screw driver.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TERRY from WAUKEE, IA
- Parts Used:
- W10721967
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
When the washer goes into a spin cycle, I would hear an intermittent loud clattering noise. I think the clutch teeth above (the cup part that is spring loaded) and the belted pulley's teeth below are not fully seating on each other during the spin cycle.
W10721967 Splutch Cam Kit
Assuming the pulley nut was properly tightened at the factory. I think this problem occurs because of ever-so-slight rounding of the splutch cam teeth from the actuator engaging and disengaging over whatever time frame there is before a clattering noise develops.
When I took off the 13mm nut using the adjustable strap tool, it felt tight to me...Was it put on as tight as it should have been at the factory? Who knows. I don't have the torque specification of this nut on that plastic pulley.
Watch the videos to remove and replace the belt cover and belt, actuator and splutch cam kit.
Pay particular attention to tightening up the nut. I put the pulley on and hand-tightened the nut. I used the adjustable strap tool and before I tightened everything, I pushed up on the pulley to press against the spring pressure in order to mesh the teeth together. After the nut was tight, I repositioned the strap tool and gave it another go, further tightening it. You see earlier that day, I only tightened it up once because I thought it was good and tight. I put everything back and within a half-hour it was clattering again and I could loosen the nut I thought was tight by hand! I fooled myself. That's why I did it twice, and don't be afraid to give it a good second tightening effort. Two weeks now and the wife is currently very happy.
Assuming the pulley nut was properly tightened at the factory. I think this problem occurs because of ever-so-slight rounding of the splutch cam teeth from the actuator engaging and disengaging over whatever time frame there is before a clattering noise develops.
When I took off the 13mm nut using the adjustable strap tool, it felt tight to me...Was it put on as tight as it should have been at the factory? Who knows. I don't have the torque specification of this nut on that plastic pulley.
Watch the videos to remove and replace the belt cover and belt, actuator and splutch cam kit.
Pay particular attention to tightening up the nut. I put the pulley on and hand-tightened the nut. I used the adjustable strap tool and before I tightened everything, I pushed up on the pulley to press against the spring pressure in order to mesh the teeth together. After the nut was tight, I repositioned the strap tool and gave it another go, further tightening it. You see earlier that day, I only tightened it up once because I thought it was good and tight. I put everything back and within a half-hour it was clattering again and I could loosen the nut I thought was tight by hand! I fooled myself. That's why I did it twice, and don't be afraid to give it a good second tightening effort. Two weeks now and the wife is currently very happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Angelo from PORTLAND, ME
- Parts Used:
- W10721967
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
The wash cycle made a loud grinding noise when it went from filling to wash.
I put the dial to drain and and pressed the pause button for 3 seconds and it drained.
Unplugged the washer from the electrical outlet .
Shut the hot and cold water off. Disconnected and drained them.
Placed the washer on a soft mat on front side exposing the back and bottom of the machine.
Unscrew the metal cover with Philips head screw driver.
Disconnect the drain hose to a bucket or small dish tub .
Remove the belt cover with 5/8 ratchet or wrench.
Using a ratchet or wrench remove the one bolt holding the clutch in place .
Remove the two Philips head screws from the shift mechanism ( looks like clock timer,my memory is failing me right now sorry! ) .
Pull down on bottom gear after removing nut.
Push in and pull down with a flat head screwdriver on the tabs holding the collar in place above the top gear .The collar and gear and spring should come apart.
Install new parts in the same order . Reassemble make sure to use Locktite 242 on the bottom nut holding the gear.
Install belt , belt guard , cover drain hose . Stand machine back up , reconnect all hoses tightly plug machine into electrical outlet and start. Put a smile on your face because you did a great job and saved yourself some money!
Unplugged the washer from the electrical outlet .
Shut the hot and cold water off. Disconnected and drained them.
Placed the washer on a soft mat on front side exposing the back and bottom of the machine.
Unscrew the metal cover with Philips head screw driver.
Disconnect the drain hose to a bucket or small dish tub .
Remove the belt cover with 5/8 ratchet or wrench.
Using a ratchet or wrench remove the one bolt holding the clutch in place .
Remove the two Philips head screws from the shift mechanism ( looks like clock timer,my memory is failing me right now sorry! ) .
Pull down on bottom gear after removing nut.
Push in and pull down with a flat head screwdriver on the tabs holding the collar in place above the top gear .The collar and gear and spring should come apart.
Install new parts in the same order . Reassemble make sure to use Locktite 242 on the bottom nut holding the gear.
Install belt , belt guard , cover drain hose . Stand machine back up , reconnect all hoses tightly plug machine into electrical outlet and start. Put a smile on your face because you did a great job and saved yourself some money!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marco from LIPAN, TX
- Parts Used:
- W11168740
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Water kept running
Safety First unplug unit, close water valves, remove upper panel with a 1/4 inch socket. Remove two screws holding the valve unplug 2 wires and replaced valve with the new one
And very impressed with the fast quick delivery of the part thank you very much
And very impressed with the fast quick delivery of the part thank you very much
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Staten Island, NY
- Parts Used:
- WPW10276397
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Socket set
The washer stopped draining.All the pump motor did was hum.
I drained the machine and pulled it away from the wall.Then I disconnected the drain hose and removed the back panel.Next,I removed the three screws holding the pump in place and disconnected the power plug from the motor.I then removed the short drain hose from the pump.Installation was the opposite of the removal sequence,and the machine worked fine right after I was done.The new part was identical the the old one,and the job was a snap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from STAMFORD, CT
- Parts Used:
- W11168740
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Cold water valve sensor no good
Took off washer body 6 screws
Took off old sensor installed new
Very simple and smooth
Took off old sensor installed new
Very simple and smooth
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jay from AMELIA CT HSE, VA
- Parts Used:
- W10804664
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
The capacitor exploded, broke the plastic cover that held it to the body of the machine and blow itself clear of the wires
I removed the back access panel and what was left of the capacitor mounting device (the capacitor (or what was left of it) was laying against the access panel). I mounted the new capacitor which had a metal strap for mounting. I removed the small, black, wire mounting device that was still plugged in to the old capacitor and slipped the wires through that device. After reviewing how to reattach the wires (it turned out the polarity on my capacitor did not matter) I plugged the wires in using the wire mounting device. Once I closed it back up everything worked fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marylou from SOUTH ELGIN, IL
- Parts Used:
- W11168740
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
No cold water being put in the washer
Turn off the water. Disconnect both hoses. Remove the plug from the outlet. Remove five screws with a nut driver from the back panel. Remove the back panel. Remove two screws from the cold water valve. Pulled out the old valve. Install new valve with the two screws. Reinstall back panel with the five screws. Reset codes to the washer. Tested out washer. Works fine.
Was this instruction helpful to you?
Thank you for voting!