11047566603 Kenmore Washer - Instructions

My dryer is on top my washer so I removed the dryer and pulled the washer out. I had to get rid of the water that was inside so I used my wet vacuum on the drain hose and sucked it out I then removed the front cover and the I tipped it back and removed two screws from the bottom of the pump bracket underneath the washer and moved the two clams on the pump hoses back to uncouple the hoses. I removed the pump and installed the new one and hocked everything back including the wires to the pump which is just a quick connect and pushed it back into place and it worked like new

Just use the video. Shows you all you need to know. Very easy. Do it yourself and it saves you money.

I used the video at parts select as a review, then just followed it. Easy de-install, reminder there's water in the line be prepared with a pot or vase to hold the water. Easy install. Washer runs perfect now. As quiet as when we bought it. I always try to fix before I re-buy, not a big green guy but I try to keep stuff working and out of land fills. Also the part was at my door in 1 day, Awsome!.

Well first of all when you buy this washer, the salesperson should tell you about checking the drain catch (ahead of the pump) and emptying out whatever get's caught in there. Never had a clue until it wouldn't work, then did a search on the internet, and darn if I didn't find specific instructions on how to open and clean out. Mine was packed full of hair pins, small change, lint, buttons, etc, all kinds of stuff. Guessing that is why the pump went out in the first place, it was so packed full that the pump could not draw any water through. But even after I cleaned it out, the pump was already shot. So called a service man, he said the pump would cost me around $200, then his labor to put it in, plus a $68 service call to just come and look at it, and $68 when he comes back to replace it. So I searched the internet for how to replace, came up with a very detailed You Tube video on how to replace Whirlpool Duet Pump. So ordered my pump from PartsSelect, just over $100, and replaced it myself. Super easy, only about 5 minutes. Thanks! —A very determined housewife!

took the old part out by the front panel and put the new pump in and now it works great. only took a couple of minute to put the new one in. thank you for saving my washer.

other than needing a new type of screw driver (not philips or flat head, but rather a starfish looking thing), the replacement was simple. took 5 minutes (after finding the correct driver)

I found a YouTube video that showed how to totally dismantle the machine. I removed the top ( easy 3 screws). Removed the bottom access panel (easy). Removed the control panel (1 Torx screw and rather tricky to unsnap). Removed the door and hinge (2 Torx screws). Removed the below retaining band (easy). Disconnected the bellow at the front panel then removed the door lock mechanism (easy). Removed the front panel (easy). Removed the bellow clamp on basket side (screwdriver hose clamp type, a little tricky but not too bad). Installed the new bellow paying close attention to the drain holes being centered on the bottom. Assembled all parts in reverse order. The really tricky part was the bellow clamp on the front panel. Patients prevailed.

After getting dress that wife denies closing in door out the repair wasant to hard. There are 3 or 4 phillips screws in back that holds top on that have to be taken out and the kick plate cover on bottom just snaps off but the rest is covered very well by other discriptions.(by the way the dress had to be thrown away so not only did i get to by bellow but a new dress also and the bellow was cheaper)

Took less than 5 minutes to replace, So Happy;-)

put in push down push back until they lock in

I watched the youtube video, then ordered the part from partselect. I then took my ipad out to the garage where I placed my washing machine and completed the removal of the old seal and installed the new one with ease. Be patient when you try and fit the new seal over the lip on the machines doorway. That was the only hard part. Once I got it started, the rest was easy. I am very happy the video was available and even easier to follow the link to order the part. Thanks! Presslerc

Removed top panel. Removed rear panel. Replaced belt. Fairly easy only issue was getting the actual belt pulled enough to wrap around the pulley.

First, I looked at a replace bellows video on U-Tube that saved a lot of time in knowing how to proceed. You really need nutdrivers as sockets won't fit on the screws. Fitting the bellows on the large drum is not as simple as it appeared in the movie. It took several attempts to get it in place, but it was simple to place the clamp after it was there. Other than that, just follow the steps in the movie for your model

First I removed the bottom panels then the door then the top then the front control panel, I had to go to different web site to get directions on how to do this, after you remove screws you have to unplug U18 from electrical control box. Then remove bumper, find wire around front of bumper and remove using needle nose pliers, then remove back of bumper from tub using phillips head screwdriver. Then with help we replaced with bumper. and put the machine back together. My complaint is there were NO instructions in the box with the bumper and the ones on your web page are not detailed enough. I had to search the web "how to remove maytag door bumper" before I found how to remove it.

I purchased the downloadable Maytag Maintenance Manual (PDF format) and followed some of the directions and pointers from this web site. All in all, it was a pretty simple process. 1) Take the top off - 3 metal screws, 2) take the control console and detergent dispenser out - 1 T-20 Torx screw and multiple plastic clips and 1 wire connector, 3) take the lower panel off - 3 metal screws, 4)take bellows retaining ring off -- spring retainer used a needle nose pliers, 4) take off door latching mechanism - 2 T-20 Torx screws and multiple clips + 3 wire connectors, 5) take front panel and door off - 4 metal screws, 6) remove bellows retaining clamp with phillips screw driver, 7) remove old bellows. Reverse the process to install new bellows. On installation, make sure that bellows drain holes are at the bottom of the door. Also, hardest and most time consuming part was installation of the metal retaining ring (spring retainer) fought with it for about a half hour before I finally got it on. BTW all metal screws for my machine were 1/4" head the remainder were all Torx T-20. Good luck!