11047799702 Kenmore Washer - Instructions

First I want to acknowledge Parts Select for their prompt delivery(received parts in less than two days)and their unbeatable prices(approximately 1/3 less than two local appliance repair/parts shops). Repair was straight forward a simple swap of the pump and I saved quite a few dollars.Thanks Parts Select.Any future appliance parts needs will be purchased here.

Very limited access to the bellow clamp. Found it easier to first remove washer front panels (8 screws total), providing ready access to R&R the bellow. 40 minutes tops.

I removed the top 3 screws on the rear, removed soap dispenser, removed screw in front corner at soap dispenser,pry off control panel with flat head screwdriver lay on top, removed spring around bellows at door opening, remove 4screws holding door assembly, disconnect 3 molded plugs serving door lock, you will need to hold door while you loosen bellows clamp.Reverse process note: soap dispenser tube can be removed to clean without any tools. It is some much easier when you remove the front door assembly.T-20 torx screwdriver, 9/32 socket Theirs a you tube video also.ghw

Looked at how the old drain pump was installed, then removed it and installed the new one. It was a fairly simple fix. The only feedback were that the parts picture was a little confusing becuase the picture didnt really look like the actual part, so we were unsure if we were ordering the correct part.

Opened lower front panel to access the motor controller. Took a picture of the wiring attached to the front of the controller. Removed two wiring harnesses and one wire with a retainer clip. Removed the faulty controller. Inserted the new controller, replaced the wiring, using the picture to insure correct positioning (although that really wasn't necessary because the wiring clips could probably only be put in the correct places). Replaced the front cover, plugged in the washer and fired it up.

Followed video clip that I found online

Followed video, slowly. Was easier then I expected. Everything fit perfectly.

Unplug washer. Open door. Look at the very bottom of the bellow and will see a spring that is connected to a small wire that runs around the bellow holding the outside on. Using a flat head screw driver insert it between the wire and bellow, pull down slighty. Grab the wire and gentley pull off. Now the outer part of the bellow will be free, pull it toward you, and off the water/soap despinser, then push it into the washer. Now look to the right side and you will see a screw head that is actully a big clamp ring around the bellow. This is the hardest part. Use a small rachet screw driver with a 7mm socket to lossen. Pull clamp off gently, you can now removwe the bellow. Put bellow back on in reverse. There will be a small tab on the bellow it goes to the top. Took about 2 hours.

pulled the front and top of the machine off, pulled off the old bellow, ordered the new bellow, and put the new bellow on. we looked on youtube.com for a video on repairing the machine.

We hired a local repairman and he even had trouble . I would not suggest anyone trying this installation on their own. It took the repair guy an hour to do and he struggled. Not an eary installation

Found it impossible to get the bellow off the machine. Removed the front spring. Even tried to but off the bellow. No luck. Called repairman. He had to take off the front panel, door panel, and the top of the machine before he could remove the back spring/clamps.

I started by dismounting the door from the washer, then placed the door on a flat counter with a towel underneath to avoid scratching. I unscrewed all the bolts securing the the frame. Once the frame was removed, I dismounted the broken door hinge and secured the new one in reverse order. Just a little time and patience. Job completed with no mess!

open the front bottom panel (3) screws. remove panel. twist off old shocks by turning the shock counter clockwise. reinstall shock by turning clockwise.

The repair went very easy after locating the repair manual inside of the washer. The service manual gave all of the codes that the machine can give. Checked the F-70 code and it stated to unplug the motor control unit. Once that was unplugged the led lights came back on and it acted like it could run again. New unit put in in less than 15 minutes. I'd suggest to have it over nights because the unit I received through UPS was very badly damaged on the outside but plugged it in and it still worked. Two weeks running and a lot of laundry later; still going well.

removed three screens on lower front panel removed hoses from pump after opening drain/filter to remove water slid pump forward and out unplugged pump wiring harness reverse to install