11045801400 Kenmore Washer - Instructions

Unplugged power cord, turned off both water valves on the wall, Disconnected the water hoses o the back where they are attached to the water inlet valve. Note: there will likely be some water left in the hoses. Then removed top lid of washer (this is a front load washer) by removing the 3 nut screws on the back of the lid and sliding it to the back and lifting off.. Disconnected the small hose that is attached to the water inlet valve by squeezing the hose clamp and sliding the hose off. Removed the 4 wires connected to the water inlet valve (marked each one with a number in order) then removed the Phillips head screw on the back of the machine holding the water inlet valve, sliding the valve to the right, . Removed valve, and replaced with new one, and re-installed by reversing order of removal.

turned off water valves , disconnected and placed hoses into small bucket . removed top . I then removed screw off old valve , shimmied it out of the hole , removed hose with pliers , slipped off white set of plugs and then black set .. Then I put hose on new valve , placed plugs ( black & white ones ) be sure to mark the correct side .. for me two white were on the right side of valve and black on left side .. placed valve back into its respective spot . attached the screw .. note I sled mine to the right just a bit and all lined up perfectly . Attached hoses , ran test cycle on warm , cold , hot .. All hoses were hooked up correctly and leak free . put lid back on and perfect .. The hardest part , was moving the shelves above my washer , really was super simple . Watch the video twice. You will be able to do it in no time. Saved me 245$ . From my appliance shop the part 150.$ 100 service call and the install fee $ since the install was so easy couldn't be much but .. Its a guesstimate ..You can do it !

My hubby and I replaced the part in about 20 minutes, including moving the washing machine. We love doing household projects like this. We're a great team and putting in this part showed how good we work together. Thanks for the quick response too!

Turned off power, turned off water supply, removed water supply hoses, removed top of washer, photographed electrical connections, removed intake hose, removed screw from part to the machine and removed valve and replaced. Reverse order to install new part and test water supply.

Go to u tube video gives instructions. Very easy to replace

Easiest repair on 2003 front loading washer. This unit cleverly uses star tool machine screws with a hex head so you can pick your favorite tool. Turn off the water supply. Remove the hot and cold hoses at the inlet valve, draining any water into a small bucket. Have a towel for dribbles. *This is a good time to examine the hoses and replace them if they are anything other than perfect. Burst or leaking hoses is the #1 cause of water damage in homes.* Three screws releases the top cover which slides 1/2 inch back and lifts off easily. Remove one screw securing the inlet valve (same size screw as the others). Pull the old inlet valve away from the rear panel for easier access. Remove the 4 wires from the solenoids (they pull straight off but maybe need a little finesse), and re-attach to the new inlet valve. Using pliers, release the hose clamp on the old valve sliding it down a couple of inches, then move the hose to the new valve and reposition the hose clamp. Toss the old inlet valve in the trash, screw the new one in place, replace the top panel, reattach and hand-tighten your hoses, turn on the water, look for any leaks, and go have a three martini lunch with the money and time you saved.

easy process: troubleshoot problem on website-- order part--get part--watch "how to replace"video on you tube-- get it done with only a screwdriver--go out for movie and dinner with $$ saved.

First took a picture and printed after disconnecting machine electric supply and removing top cover. removed screw holding vale in place, removed wiring .removed valve,attached wires to new valve inserted in place attached tubing and installed mounting screw and hoses, checked all again and tested

Removed covers per instruction video provided by website

We do not wish to have our repair published. The part itself was perfect and corrected our leaking problem but we did have difficulty with the installation despite detailed instructions. We appreciate a good price for the perfect part!

Simple repair. #20 Torx, pair of pliers and 10 minutes to complete the job. Part was exact fit. Turned off the water supply, removed the three screws at the back, slid the top to the back and lifted it off to reveal the valve. Removed the screw holding the valve in place, slid the valve to the right and pulled the valve out to the inside. Used pliers to move the hose retainer off the valve, removed the hose, unplugged the wires, and reversed the procedure to install the new valve.

Remove top 3 screws.
Remove 1 screw that holds inlet valve.
slide valve to the right.
Mark and remove 4 connector wires.

Reverse order to install.

Replaced inlet valve. Took top cover off. Accessed inlet valve. Removed hoses. Replaced valve. Works like a charm.Corrected problem

It was fast and pretty easy to do.

disconect wayer inlet hoses.remove screws that hold the top cover. This will expose the water inlet valve. remove the defective valve and any other associated clamps,hose etc. test run for leaks.