11045976404 Kenmore Washer - Instructions

I just take out the botton part and fine what part what i need chage and just chage exactly like the old if yoo dot remember all the wires please take pictures and you hava guia to check went you are finished

First I want to acknowledge Parts Select for their prompt delivery(received parts in less than two days)and their unbeatable prices(approximately 1/3 less than two local appliance repair/parts shops). Repair was straight forward a simple swap of the pump and I saved quite a few dollars.Thanks Parts Select.Any future appliance parts needs will be purchased here.

Very limited access to the bellow clamp. Found it easier to first remove washer front panels (8 screws total), providing ready access to R&R the bellow. 40 minutes tops.

It was easy as soon as I previewed a video on how to repair bellow it was all about unscrewing some screws and removing some parts but was simple steps that anyone can do themselves only thing that gave me very little trouble was putting the spring coil around the bellow needed my husband to help me a little so it wouldn't come out place while stretching the spring to make sure everything was good and secure and ran a test washer to make sure it didn't leak afterward.the baffle was very easy to replace with very little pressure I was able to slide it till I heard a click sound and it was secure did laundry same day and every was wonders very happy I was able to save some money on labor :)

I removed the top 3 screws on the rear, removed soap dispenser, removed screw in front corner at soap dispenser,pry off control panel with flat head screwdriver lay on top, removed spring around bellows at door opening, remove 4screws holding door assembly, disconnect 3 molded plugs serving door lock, you will need to hold door while you loosen bellows clamp.Reverse process note: soap dispenser tube can be removed to clean without any tools. It is some much easier when you remove the front door assembly.T-20 torx screwdriver, 9/32 socket Theirs a you tube video also.ghw

We followed another very helpful repair story. Unplug machine. Unscrew top back screws, remove top of washer. Reach inside from the top in the front of the machine. Remove screws holding latch in place, unplug the three plugs attached to latch. Replace with new door latch, screw it in place, replug the three plugs, put top of machine back on, replace screws on back and your'e done! Works great! Job made easy thanks to others helpfulness!

Made a bad call after googling "bearing squeal for HE 4t" and replaced the bearings and seal on the drum.... Turns out my squeal was coming from the drain pump, didn't realize until after a major tear down and replacement of bearings and seal. Managed to break one of the electrical connectors on the heating element on that repair as well... Compared to the bearing replacement the drain pump was super simple. Lots of good instructions above, the only thing I would add is that if you put a little pressure on the hose clamps and spin them to an easier position to see and get pliers on, they will be much less of a headache. Vice grips were the best tool for getting them released and re-installed. The heating element was pretty easy, loosen the center nut to the end of the threads but don't remove. Use a flat screwdrive to gently pry the unit out. Use a little dish washing soap to lube up the rubber plug on the new one before installing and it slides right in.

Washed three loads and it was ok but then it stopped draining again. I don't know what to do.

I replaced the pump thinking this was the most likely cause of the problem. The pump is easy to access and get to. The reviews were helpful. The hose clamps were difficult to get back in place especially the one from the washer drain to the pump (need wide-jaw pliers). Now that I have seen the system work, the pump was not bad and the water from the drain still smells bad. I just ordered the filter 8181683, which looks like the only other thing that would prevent the water from draining completely. The drain hose is not blocked.

Looked at how the old drain pump was installed, then removed it and installed the new one. It was a fairly simple fix. The only feedback were that the parts picture was a little confusing becuase the picture didnt really look like the actual part, so we were unsure if we were ordering the correct part.

The difficult part was getting the water from the washer without making a huge mess. I used a shop vac loosened the cover on the filter/strainer assembly use the shop vac to suck up the water before spills all over. if the tub is full I dumped my shop vac twice total. 1 Remove pedestal drawer 2 removed lower cover to expose mechanicals and pump assembly 3 vac out the water by using above procedure. 4 rotate hose clamps to a position where you can get the needle vice grip on them/remove hose clamps. 5 lift cover exposing electrical connections on the pump assembly depress tab slide connector out. 6 remove 1 torx head screw securing pump to base of washer. 7 remove pump assembly. 8 Reinstall in reverse of above instruction. I also took the lower tub hose off and washed, bleached along with hot water to. clean it

repair was a cake-walk with the video there to help.Thanx

open the front bottom panel (3) screws. remove panel. twist off old shocks by turning the shock counter clockwise. reinstall shock by turning clockwise.

Took the front panel below tub and above pedestal off washer. Removed pump and found coins in the strainer. Removed them thinking they may be causing the problem. Put everything back together and tried again. Washer still wouldn't drain. Unplugged it and ordered a new pump. Installed pump after removing the plug and draining water from washer. Replaced pump with new one and washer works like new.

Of course the machine was not plugged in & water valves where off. I took water hoses off. Then i took 3 screws off the back of lid & slid lid back & lifted it off. I then unplugged two wires going to valve. I then took water hose going to valve off. Last there is one bolt holding valve to machine & in the mechanic industry we call this bolt a star head, so it was a good thing I had this tool. So if you do this repair you will have to get this tool. This job is easy to do & Part Select was 100% on my order & shipping! I will order again when something brakes again !!! Thank's