11045862403 Kenmore Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- claude van from big sandy, TN
- Parts Used:
- WPW10388414
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
tub would not turn
take the back cover off and put belt on. the belt is a tight fit and requires sone effort, but can be done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- FRANCIS from leesburg, FL
- Parts Used:
- WP8182634
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
door would not latch , and lights on front just flashed
1)I removed the bottom front panel,reached up the right side of the machine and pulled the manual release on the bottom of the latching mechanism.2)I then removed the top to the machine in order to gain access to the latch. 3)I removed three electrical connectors then the three mounting screws using a #15 Torx driver. I then reversed the reverse procedure to install the new latch. total time to do the job was less than half an hour. Machine works OK.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Dallas, TX
- Parts Used:
- WP8181694
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Small water leak into washer when not being used
Unplugged and disconnected water lines. Removed three machine screws on the back edge of the washer top. Lifted the back and then pulled it to release it from the front. Removed 1 screw from the back next to the hot water connection. Slide the water valve assembly over to the left if you are standing in front of the washer and it pops out. Then slide the hose clamp for the small hose off and use flat head screw driver to pry hose loose. Then use flat head to gently work connectors off. Then reinstall everything in reverse order. Reconnect water lines turn on water and watch water leaks before cover is reinstalled.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darrell from Lady Lake, FL
- Parts Used:
- 280187
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Pump not working
Replaced pump
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- scott from DENVER, NC
- Parts Used:
- WP8182233
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
One of my baffles just came off during a wash, one of the plastic clps that hold it in place dry rottedafter 10 years
Real easy , the baffle goes in only one way , use the others as guide as too which side the taller end goes.
With one hand pushing in the center of the back of the basket , pushing back , simply place and slide baffle towards you with other hand , there will be a crisp snap as it slide in to place.
With one hand pushing in the center of the back of the basket , pushing back , simply place and slide baffle towards you with other hand , there will be a crisp snap as it slide in to place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Douglas, AL
- Parts Used:
- WP8182119
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Replace Bellows between door and tub
Remove top and front
Care taken to unplug door wiring
should have taken notes or photos where srews go and order
remove old bellows large hose clamp and sping tensioned clip
clean surfaces
install new bellows on tub only
put all panels and door together
Connecting wiring to door and strain relief takes 2 people
connect bellows to door with spring clip
Care taken to unplug door wiring
should have taken notes or photos where srews go and order
remove old bellows large hose clamp and sping tensioned clip
clean surfaces
install new bellows on tub only
put all panels and door together
Connecting wiring to door and strain relief takes 2 people
connect bellows to door with spring clip
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carolyn L. from CLAYTON, NY
- Parts Used:
- WPW10467168
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Washer leaking
Followed internet instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from Amherst, OH
- Parts Used:
- WP8182634
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Washing machine wouldn't run. Kept making buzzing sound and didn't show door latched.
Removed the 3 screws that hold the bottom front panel in place. Removed the 3 screws that hold the door latch in place and pulled out on the bottom of the door which wasn't very much and slid the door latch out to get to the wire connections. Connected the wires to the new latch and pulled out bottom again and put the latch back into place and put the 3 screws back in. Note: make sure you unplug the washer so you don't have a chance to get shocked. Level of difficulty was pretty easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from RUSSIAVILLE, IN
- Parts Used:
- WP8181694
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Water would accumulate in the washer drum over several days of non use
Repair was very simple. First watch the video that is available on this website. The installation went exactly like the video described. I pulled the washer away from the wall a few inches. Removed the three screws that hold the top on. Removed the top. Shut off the water and removed the water lines. Removed the single screw that holds the inlet valve in place (T20 torx).Removed the inlet valve, removed the hose from the valve. Reversed the operation to re-install. About a 20 minute job, tops. Tested the washer when finished and it worked great. It has been a couple of weeks now and no water has accumulated in the drum.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Evette from Mayfield, NY
- Parts Used:
- 280187
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
the pump wasnt puping out the water
firts remover the three bolts that held the front panel on, and removed that. Then removed the screw that held the pump in place. then removed the hoses from the pump. After that put hoses on new pump and srewed back in place . the put front back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robin from Gary, TX
- Parts Used:
- 280187
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The washing machine was not draining. It was showing a code on the washer of 02.
We removed the front cover to the washer. Then we removed the drain pump piece that was broken. We put the new drain pump in and secured the screws. We also inspected all the hoses to make sure the hose clamps were intact. Then leaving the front cover off the machine to inspect for leaks we turned on the wash cycle. No more problems.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from GOUVERNEUR, NY
- Parts Used:
- WP8182233
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
drum baffle broke and had to be replaced
place new baffle over slots in drum; move toward back of drum and snap in to place pressing down and moving toward front of drum
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from Brooklyn, NY
- Parts Used:
- WP8181694
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
I find water in the drum after a few days of non use
Removed the three screws in the back took off the top and swamped out the part. I recommend that the inlet valve is checked periodically by removing the hoses to see if there's any build up on the filter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from VIRGINIA BCH, VA
- Parts Used:
- WPW10467289
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Replacing the heat sensor following an F-24 Error Notice.
I followed your repair video explicitly, simple fix. However, one should
be careful when disconnecting the two prong electrical connector from
the heat sensor. the two black wires can pull free easily. In that case, the
rear of the female plastic wired connector must be extracted to allow the two black wires to be "pushed" into the narrow slot which displaces the
wire insulation and allows for a good electrical connection. If a punch tool is not available a pair of needle nose pliers works. Also, observe
the orientation slots on both the male andfemale connectors - they
connect one way only! I set the washer on it's face while effecting this
repair to better see what I was doing (eyesight not as good as it used to be). Thanks for the timely support!
be careful when disconnecting the two prong electrical connector from
the heat sensor. the two black wires can pull free easily. In that case, the
rear of the female plastic wired connector must be extracted to allow the two black wires to be "pushed" into the narrow slot which displaces the
wire insulation and allows for a good electrical connection. If a punch tool is not available a pair of needle nose pliers works. Also, observe
the orientation slots on both the male andfemale connectors - they
connect one way only! I set the washer on it's face while effecting this
repair to better see what I was doing (eyesight not as good as it used to be). Thanks for the timely support!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from LORAIN, OH
- Parts Used:
- WPW10467168
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Replace tub to pimp hose.
Factory hose clamps were awkward to maneuver. I used automotive radiator hose clamps instead. They worked great.
Was this instruction helpful to you?
Thank you for voting!