11047787801 Kenmore Washer - Instructions

We do not wish to have our repair published. The part itself was perfect and corrected our leaking problem but we did have difficulty with the installation despite detailed instructions. We appreciate a good price for the perfect part!

Checked for 120 V AC at pump connector. It was present . Pump was hot. Ordered new pump. Changing the pump is a piece of cake. Just tilt machine back and rest on a brick. Remove 3 5/16th screws . Disconnect 2 hoses and 1 plug. Took 10 minutes tops. Back in business.

Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.

This was an easy fix . PartSelect was quick and had all the info I needed to repair my washer. Plus shipping was super fast. Thanks

took the old part out by the front panel and put the new pump in and now it works great. only took a couple of minute to put the new one in. thank you for saving my washer.

First thing, unpluged the washer. I removed the lower front acces panal. I then propped the washer up on 2 pint sized paint cans to reach the pump mounting screws. I disconnected the wire bundle going to the pump. Then removed the inlet and outlet hoses from the pump. Then I removed the 2 mounting screws on bottom and slide the pump to the left and removed. I then pump the new pump on the same way I took the old one off, but in reverse. Easy and fast the worst part was the price of the pump.

Old belt and new belt were not exactly the same. did research and deturminded that the new belt was correct. Reomoved the back panel and rolled the old belt off. Pully is designed to allow changing of the belt without taking the pully off. Put new belt on the motor pully ensuring it was in the groves. started belt on the drum pully and turned it untill it was tight. With an open hand I held the belt on the drum pully so it would not slip off and gave the drum a quick turn to jump the belt onto the pully. rotated the system several turns to make sure everything tracked correctly. Replaced the back panel.

First unplug the washer. Make sure and drain washer completely. If not drained remove front panel , Remove 2.5 inch Plastic drain cover which has a catch bin on it. This will allow it to drain the washer. Put pan underneath to catch the water. Tip washer back and prop up with something 6 inches tall to get to the screws underneath. A cement block would work well. Use pliers to squeeze hose clamp together to remove the Hoses. Gently lift up The flip down cover Over the top of the wire harness Push in the tab on the wire harness, Gently pull back on the wire harness. Remove two mountings screws from the bottom of the washer. Slide the whole pump housing to the right and Lift up. Now the pump is been removed. Inspect inside the hoses For Debrie. Remove anything that is left in the hoses. Reinstall the pump in reverse order from the way you took it off. Leave front panel off Make sure all hoses and wire harness are hooked up. Run wash cycle to make sure there are no leaks. Do not put hands in while running. If no leaks replace front panel. Not sure if this is the right way But this is the way we did it and it worked well. Washer runs quieter now than it did when we got it

Read the instructions provided by PartSelect.....and with a bit of patience I installed all four bolts so the washer's inside agitator was not damaged in shipping. I highly recommend that anyone who is moving/storing or shipping their washer that you find the correct shipping bolts according to your model and make and install them prior to moving your appliance.

Removed top of washer and replaced flow meter.

repair was a cake-walk with the video there to help.Thanx

I had replaced the flowmeter, but that didn't solve the problem, so I ordered the hot/cold solenoid fill part. Other than ONE screw that was unique -- the back retaining screws were nut driver screws, the one retaining screw was a torx which, of course, couldn't be seen unless you pulled the washer all the way out. Unscrewed that, unhooked the hose clamp with pliers and worried the hose off, removed the four electrical connections (which were TIGHT) and replaced the part. Turned on the water and was dismayed to get a d/l error code. After some colorful language learned from my drill sergeant 40 years ago, I realized that was "door lock" and closed the door tightly. Ran great and the Mrs. thinks I'm a hero.

Well first of all when you buy this washer, the salesperson should tell you about checking the drain catch (ahead of the pump) and emptying out whatever get's caught in there. Never had a clue until it wouldn't work, then did a search on the internet, and darn if I didn't find specific instructions on how to open and clean out. Mine was packed full of hair pins, small change, lint, buttons, etc, all kinds of stuff. Guessing that is why the pump went out in the first place, it was so packed full that the pump could not draw any water through. But even after I cleaned it out, the pump was already shot. So called a service man, he said the pump would cost me around $200, then his labor to put it in, plus a $68 service call to just come and look at it, and $68 when he comes back to replace it. So I searched the internet for how to replace, came up with a very detailed You Tube video on how to replace Whirlpool Duet Pump. So ordered my pump from PartsSelect, just over $100, and replaced it myself. Super easy, only about 5 minutes. Thanks! —A very determined housewife!

I opened the top by taking four screws from the back and lifted the top. The part to be replaced was clearly in view. I opened the clamps on the hoses, pulled the hoses off, removed the wires, and reversed the process with the new part. The washer works great now! I ordered the part on a Friday, and it was delivered the next day, even though I didn't pay for overnight!

unplug washer from outlet carefully tilt back to get at underside of washer remove bottom panel. pump location lower right front. remove two hoses from back using pliers keep note on hose location. remove two bolts on underside of machine slide pump to the right to release from rubber holders to install reverse the process also good idea to use the new hose clamps that come with your new pump and the rubber mounts if they are included