41740412703 Kenmore Washer - Instructions

(This is reply #2 of 2)
After I finally got all of the parts (at least the rear brackets and screws) I found that the panel only had one of two holes for the two horizontal screws.
After drilling a new hole in the left rear bracket position, I discovered that the 2 screws could not be threaded into the bracket pilot holes. Theyt froze up at the top of the taper in the threads. I had to increase the size of the hole 1/64" to get the screws in. There also is a trick to getting the bracket through the punched out hole in the panel- you must angle the bracket corner to corner then apply about 10# of preasure to the bracket to force it through the hole.
Other than that, the panel install went pretty well. Now I have to get the front brackets and springs and screws which are on backorder...

I watched the videos and replaced the shocks and suspension springs. This worked to stop the unit bouncing completely and cut the banging noise in half. Further diagnosis revealed a damaged drum and outer shell. The repair itself was very simple and didn't require special tools or skills. There is a tricky shock absorber locking pin on the right shock bottom position. There is a control box of some sort that prevents the complete removal of the pin without breaking it. On install, I simply pushed the pin through from the front. Ultimately, I ended up replacing the unit. However, I found the site to be extremely helpful. Great service.

Simple install, remove the two screws holding the pump motor.
Loosen the two hose clamps that hold the hoses in place.
Pull out old pump motor.
Place new pump into place, and install mounting screws and tighten.
Slip drain hoses onto new pump and reinstall clamps.
Check for leaks.
Done.

It was very good. They should have mentioned about the wire and spring to remove the rubber strip though. Found out about that in comments! Otherwise, very good!

Watched a u tube video and did it myself and I'm a 58 year old woman who has never worked on a washer before!

Repair was easy watched video it was spot on I went to auto parts store and bought 2 screw clamps to replace the spring clamps and made repairs easier washer works great happy wife

Removed and replaced two screws.

Took door lock switch out and fished out broken part. Reinstalled switch and installed new striker. Problem solved. Ordered extra striker just in case.

It was a very easy fix. Called a repairman and they wanted 350.00 to come out. Ordered the door lock and switch assembly for 76.00 and it was fixed in 15 minutes. Thank you for shipping the part so fast. Much appreciated.

Let's see...removed lower panel-used tools to unscrew the unit---one piece-nice to replace---EASY to replace! Removed hose---placed hose on new unit; screwed all back to bottom of washer-replaced lower panel...Voila! Made sure unit was balanced...did a load of whites---Awesome WASHER NOW!!!

"Instructions" with the kit suggest pulling the pins out with a pair of pliers. That's fine if you're a gorilla. It's easier to use a 13MM boxed-end wrench. Slip it over the tapered end to depress the locking tab; then tap a 3/8 dowel rod held against the tapered end to remove the pin. Also my washer has a drain tube that has to be disconnected to get access to the top pin. If I had to do this again it would take about an hour.

For some time, our washer's door was vibrating and making noise during the spin cycles. Then after washing a large blanket, the drum stopped spinning all together. I was able to slide the top of the washer off after undoing the screws in the back and then following the directions, found that the error code was for the washer door. The drum would not spin because it thought that the door was open, confirming what we thought, the door lock and switch assembly were bad.
I was able to unscrew the assembly from the front, then reach down and after ordering the new part, disconnect the 3 cables, remove the old part then redo the cables on the new assembly and Voila...working washer, woo hoo!

First unplug the machine, then remove two srews on the back of the machine for the top cover. Remove top cover and then remove two srews that hold the door locking part. Put your hand in the machine and grab the part. unplug the three wire harnessess then plug them back and put back in place and put the two srews back and then the top cover and two srews as well.

Removed spring retainer straps from top of springs. Propped up tub with blocks and a wedge. Lifted out each spring and replaced. Re-attached spring retainer straps. Removed pins from shock absorbers (old/broken ones). These break due to moving washer w/out installing original foam blocks and support screws or due to age and fatigue. Pins have a retainer that must be depressed as you pull or push them out. may need to spin back and forth with pliers as you pull them. Bottom right pin won't come out w/out a hassle. Cut it in pieces with dykes and used spare pushed in from the FRONT (not the rear, as it was originally installed). Found leak was not fixed by getting the drum back up to proper height. Found bolt on tub had broken the bottom of the soap dispenser "tray". This is a 50.00 part. Made a patch from the bottom. Roughed up plastic and used silicone adhesive. After it had adhered filled from top with more silicone. Allowed 24 hrs to dry. Washer is as good as new.

The instructions that come with parts say to pull pins out with pliers. not much room to do that. I used hammers and punches where I had access and prybars nail puller an hammer to offset where the water outlet was in the way. I used a short handle hammer to install three of the pins. The third I used a prybar and spacer blocks.