11047566601 Kenmore Washer - Instructions

Searched internet for diagnosis. Ran diagnostic test using the diagnostic manual from whirlpool. The error code was F29. Replaced door latch but problem was not solved. Then order the Motor Control Unit. Removed old control unit through the top by removing the top washer cover and numbering harness positions with painter's tape. Install the new Control Unit and ran diagnostic procedure. The problem was solved. The washer is working fine.

other than needing a new type of screw driver (not philips or flat head, but rather a starfish looking thing), the replacement was simple. took 5 minutes (after finding the correct driver)

Removed top panel. Removed rear panel. Replaced belt. Fairly easy only issue was getting the actual belt pulled enough to wrap around the pulley.

First, I looked at a replace bellows video on U-Tube that saved a lot of time in knowing how to proceed. You really need nutdrivers as sockets won't fit on the screws. Fitting the bellows on the large drum is not as simple as it appeared in the movie. It took several attempts to get it in place, but it was simple to place the clamp after it was there. Other than that, just follow the steps in the movie for your model

First I removed the bottom panels then the door then the top then the front control panel, I had to go to different web site to get directions on how to do this, after you remove screws you have to unplug U18 from electrical control box. Then remove bumper, find wire around front of bumper and remove using needle nose pliers, then remove back of bumper from tub using phillips head screwdriver. Then with help we replaced with bumper. and put the machine back together. My complaint is there were NO instructions in the box with the bumper and the ones on your web page are not detailed enough. I had to search the web "how to remove maytag door bumper" before I found how to remove it.

Well first of all when you buy this washer, the salesperson should tell you about checking the drain catch (ahead of the pump) and emptying out whatever get's caught in there. Never had a clue until it wouldn't work, then did a search on the internet, and darn if I didn't find specific instructions on how to open and clean out. Mine was packed full of hair pins, small change, lint, buttons, etc, all kinds of stuff. Guessing that is why the pump went out in the first place, it was so packed full that the pump could not draw any water through. But even after I cleaned it out, the pump was already shot. So called a service man, he said the pump would cost me around $200, then his labor to put it in, plus a $68 service call to just come and look at it, and $68 when he comes back to replace it. So I searched the internet for how to replace, came up with a very detailed You Tube video on how to replace Whirlpool Duet Pump. So ordered my pump from PartsSelect, just over $100, and replaced it myself. Super easy, only about 5 minutes. Thanks! —A very determined housewife!

I removed the three bottom screws and removed the plate. Removed the control panel, removed the star screw on the left side and pulled off the front panel of the machine. Loosen the bellow clamp with a phillips head and pull off the front spring clamp on the bellow. Pull off the old bellow and re installed the new one. Installed and tightened the bellow clamp and spring loaded clamp on the front of the bellow and re installed the panel, and control panel. Checked for leaks.

First thing, unpluged the washer. I removed the lower front acces panal. I then propped the washer up on 2 pint sized paint cans to reach the pump mounting screws. I disconnected the wire bundle going to the pump. Then removed the inlet and outlet hoses from the pump. Then I removed the 2 mounting screws on bottom and slide the pump to the left and removed. I then pump the new pump on the same way I took the old one off, but in reverse. Easy and fast the worst part was the price of the pump.

My dryer is on top my washer so I removed the dryer and pulled the washer out. I had to get rid of the water that was inside so I used my wet vacuum on the drain hose and sucked it out I then removed the front cover and the I tipped it back and removed two screws from the bottom of the pump bracket underneath the washer and moved the two clams on the pump hoses back to uncouple the hoses. I removed the pump and installed the new one and hocked everything back including the wires to the pump which is just a quick connect and pushed it back into place and it worked like new

I used the video at parts select as a review, then just followed it. Easy de-install, reminder there's water in the line be prepared with a pot or vase to hold the water. Easy install. Washer runs perfect now. As quiet as when we bought it. I always try to fix before I re-buy, not a big green guy but I try to keep stuff working and out of land fills. Also the part was at my door in 1 day, Awsome!.

I watched the video and it really was as easy as it looks. Great shipping time, I ordered the pump Monday and it arrived on Thursday, standard ground shipping!

Just use the video. Shows you all you need to know. Very easy. Do it yourself and it saves you money.

A previous person had broken the actuator switch connection so I replace it and got rid of the error code. But water poured out and I eventually took off the whole dispenser assembly and found a sock had stopped the big hose up where it enters the outer wash drum.

Perfect part...saved me hundreds on labor. Thanks!

I was already very familiar with the motor & drain pump, as I had disassembled my original one in attempt to find the problem & fix it. Finally, I broke down & purchased a new one. It was VERY easy to install! The most difficulty was finding the right sized board to put underneath & raise the machine up (with the dryer attached to the top of it) to place the board underneath so that I could tighten the bolts from underneath to attach the pump. After that was over, the rest was cake! Just attach the hoses & the electrical, which just clips in place & my washer is like new again! Yay! Oh, and yes, I'm a woman DIY'er.