11045986404 Kenmore Washer - Instructions

When I looked at the website for latch repair they showed a video (can't remember which brand but not Amana) where you had to take off the top and front of the washer to get at the latch part on the washer. For the Amana I had, you simply had to pull out a portion of the rubber gasket held onto the washer by a wire/spring combination (you can take the wire off) to get at the latch assembly. You could then undo the three screws holding the latch to the washer, pull it out and unplug the three wiring connections to remove the old latch. Then plug connections into the new latch, reinstall, tighten screws and fit gasket and wire/spring assembly back together. Much easier than going thru the top and front of the washer!

Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.

Unplug machine,remove three screws that hold on top cover.
Unplug latch switch assembly,then open front door of washing machine, remove three screws which hold latch
switch. Install in reverse order.

This was an easy fix . PartSelect was quick and had all the info I needed to repair my washer. Plus shipping was super fast. Thanks

I ordered the part, followed the instructions listed on appliance help and put it in... easy

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

It was easy as soon as I previewed a video on how to repair bellow it was all about unscrewing some screws and removing some parts but was simple steps that anyone can do themselves only thing that gave me very little trouble was putting the spring coil around the bellow needed my husband to help me a little so it wouldn't come out place while stretching the spring to make sure everything was good and secure and ran a test washer to make sure it didn't leak afterward.the baffle was very easy to replace with very little pressure I was able to slide it till I heard a click sound and it was secure did laundry same day and every was wonders very happy I was able to save some money on labor :)

First I want to acknowledge Parts Select for their prompt delivery(received parts in less than two days)and their unbeatable prices(approximately 1/3 less than two local appliance repair/parts shops). Repair was straight forward a simple swap of the pump and I saved quite a few dollars.Thanks Parts Select.Any future appliance parts needs will be purchased here.

Made a bad call after googling "bearing squeal for HE 4t" and replaced the bearings and seal on the drum.... Turns out my squeal was coming from the drain pump, didn't realize until after a major tear down and replacement of bearings and seal. Managed to break one of the electrical connectors on the heating element on that repair as well... Compared to the bearing replacement the drain pump was super simple. Lots of good instructions above, the only thing I would add is that if you put a little pressure on the hose clamps and spin them to an easier position to see and get pliers on, they will be much less of a headache. Vice grips were the best tool for getting them released and re-installed. The heating element was pretty easy, loosen the center nut to the end of the threads but don't remove. Use a flat screwdrive to gently pry the unit out. Use a little dish washing soap to lube up the rubber plug on the new one before installing and it slides right in.

Washed three loads and it was ok but then it stopped draining again. I don't know what to do.

Removed the 3 bolts attaching top of washer. Disconnected hoses from the inlet value and flow meter, also very careful to remove the wire connections. Removed Water inlet valve (this requires the star screw driver). Did find it best to connect the inlet valve and flow meter before reattaching the inlet valve, as that sits under the lip, it is just a bit of a tight fit to get the hose reconnected between the two. Then reconnected the flow meter hose to the dispensing box, reattached the hoses and ran a cycle no f20 issues, as a note, an f20 has to do with a restriction in the flow of water not with pressure so not sure if it was the inlet valve or flow meter clogging up or both.

Very limited access to the bellow clamp. Found it easier to first remove washer front panels (8 screws total), providing ready access to R&R the bellow. 40 minutes tops.

Looked at how the old drain pump was installed, then removed it and installed the new one. It was a fairly simple fix. The only feedback were that the parts picture was a little confusing becuase the picture didnt really look like the actual part, so we were unsure if we were ordering the correct part.

I removed the top 3 screws on the rear, removed soap dispenser, removed screw in front corner at soap dispenser,pry off control panel with flat head screwdriver lay on top, removed spring around bellows at door opening, remove 4screws holding door assembly, disconnect 3 molded plugs serving door lock, you will need to hold door while you loosen bellows clamp.Reverse process note: soap dispenser tube can be removed to clean without any tools. It is some much easier when you remove the front door assembly.T-20 torx screwdriver, 9/32 socket Theirs a you tube video also.ghw

We followed another very helpful repair story. Unplug machine. Unscrew top back screws, remove top of washer. Reach inside from the top in the front of the machine. Remove screws holding latch in place, unplug the three plugs attached to latch. Replace with new door latch, screw it in place, replug the three plugs, put top of machine back on, replace screws on back and your'e done! Works great! Job made easy thanks to others helpfulness!