11047089601 Kenmore Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Day from Basking Ridge, NJ
- Parts Used:
- WP8182233
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Baffle was worn out/broken
No instructions needed. Very easy to replace. You guys are great! Much cheaper than others and delivered next day! You are now on my "favorites"!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LAURA from SPARTA, KY
- Parts Used:
- 280187
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
washer not drain or spin
it was a really easy fix. unclamped the 2 hoses and took out screw, removed water pump. Connected two hoses back and set in place then screwed in locking screw. could not have been any easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from PALESTINE, IL
- Parts Used:
- WP8182862
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Whirlpool front load washer drum filling with water after use.
Followed the installation video instructions. Removed the washer top with a 1/4” nut driver torx bit. Shut off and unhooked the water lines to the washer. Took one screw off of the solenoid valve on the washer back. Removed the water line on the solenoid on the inside with a pair of pliers. Installed the new solenoid in reverse order. It took maybe 10 minutes to take off and replace. Very easy to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gopaul from Queens, NY
- Parts Used:
- WP8182119
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Bellow was damaged,water leakage.
First,we took apart the front of the washer and then we removed the old bellow and put the new one on.After we put back up the front of the washer and open the door to put the clamp on then after we unlocked it.After it was working good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martin from Kotzebue, AK
- Parts Used:
- 280187
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Pump not draining the water out.
First I made sure the washer was unplugged from the outlet and I took out 3 screws that held the front panel and removed it to get access to the pump.
I disconnected the electrical plug to the pump and there were 3 phillips head screws that held the pump in place that needed to removed. Pulled out the old pump and slide the new one in it's place with no prorblems. Tighten the 3 screws on and plugged it back in and away we went washing clothes again.
I disconnected the electrical plug to the pump and there were 3 phillips head screws that held the pump in place that needed to removed. Pulled out the old pump and slide the new one in it's place with no prorblems. Tighten the 3 screws on and plugged it back in and away we went washing clothes again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from OMAHA, NE
- Parts Used:
- WPW10467168, 280187
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
PUMP HOUSING LEAKS
REMOVE AND REPLACE. FLEXIBLE RUBBER CONNECTOR WAS NOT A EXACT REPLACEMENT, THE ORIGANIL HAD A BACK STOP VALVE, NOT SURE OF THE EFFICATE ON MACHINE.
Was this instruction helpful to you?
Thank you for voting!
Torn bellow lip
Replace bellow with help from Youtube video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from SAN MARCOS, TX
- Parts Used:
- WP8540015
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Multiple water leaks, all rubber parts are chewed up from a mouse 1/
1/4 inch nutdriver, took the top and the front panel of and renew all rubber parts / hoses. It looks less than 1 hours. All parts like factory quality, everything fits perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from TARPON SPGS, FL
- Parts Used:
- W10822553
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Spring balanced tub violent shake on spin
Washer was on a 13 inch high platform I built for front.load Heat washer and dryer. Removed 3.screws from bottom of front panel and had access to all 4 shocks..front and rear. All shocks were unattachedeither at base or on tub. Easy to install all 3 from front without moving Mach. I figured if 1 or 2 shocks failed the violent.movement broke the other 2. Purrs like.a.kitten now. No bearing.or spring.damage.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from WAKE FOREST, NC
- Parts Used:
- WP8182862
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Low water flow into dispenser and washer tub
Super simple repair, videos on this site were spot-on.
1. Turn off water, unplug washer, and disconnect the hoses from the back of the washer.
2. Remove the three T20 torx screws holding on the top of the washer, slide the top back about an inch, and lift off.
3. Remove the T20 torx screw holding the water valve to the back plate of the washer.
4. Using pliers, release the hose clamp on the outlet hose of the valve and slide it down about an inch.
5. Remove the old valve and attach the new one to the outlet hose. Reinstall the hose clamp.
6. Replace the screw that holds the valve to the back plate and reinstall the top of the washer. Reconnect hoses the the washer, turn on water, and plug back the washer back in.
7. Odds are, your water flow has been low for a while and the first cycle is going to flush a good bit of mildew and other gunk into the washer drum. Run a cleaning cycle with about 1/3 cup bleach through the washer prior to using.
Should be good to go!
1. Turn off water, unplug washer, and disconnect the hoses from the back of the washer.
2. Remove the three T20 torx screws holding on the top of the washer, slide the top back about an inch, and lift off.
3. Remove the T20 torx screw holding the water valve to the back plate of the washer.
4. Using pliers, release the hose clamp on the outlet hose of the valve and slide it down about an inch.
5. Remove the old valve and attach the new one to the outlet hose. Reinstall the hose clamp.
6. Replace the screw that holds the valve to the back plate and reinstall the top of the washer. Reconnect hoses the the washer, turn on water, and plug back the washer back in.
7. Odds are, your water flow has been low for a while and the first cycle is going to flush a good bit of mildew and other gunk into the washer drum. Run a cleaning cycle with about 1/3 cup bleach through the washer prior to using.
Should be good to go!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from AUSTIN, TX
- Parts Used:
- WP8182862
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
The inlet valve begins to restrict water flow into the washer based on normal calcium buildup. At a certain point, the washer will start giving an F20 error code indicating it is not getting enough water.
This is a straightforward replacement. Move the washer to an area where you can work on it. Unplug the washer from the wall. Turn off the water and disconnect the hot and cold water hoses at the washer. Remove the back of the washer. Slide out the top of the washer. Remove the small hose from the valve to the remainder of the washer. Disconnect the two control wires to the valve. Replace the valve. Replace the small water hose. Reconnect the wires. Replace the top and back of the washer. Connect the water back up. Plug in and try a test load. The water should flow fast enough to reach the back of the machine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from JACKSONVILLE, FL
- Parts Used:
- WP8183202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Broken hinge
Removed door from washer, remove hinge from door. Then slip in hinge and tighten hinge to door. Then attach door. It works and the most important thing the wife is happy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Helen from NASHUA, NH
- Parts Used:
- WP89503
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Leaking water inlet hoses.
Removed the old hoses and screwed on the new hoses.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Francisco from DELTONA, FL
- Parts Used:
- WP8182862
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Tub filling when power was off due to inlet valve leak.
Followed instructions as shown on repair video at site.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from YARDLEY, PA
- Parts Used:
- WPW10110225, WP8182862
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set
Inlet valve was stuck in open position allowing washer to fill with water when not in use.
Removed lid. Took old parts off and replaced with new parts. Also replaced hoses while washer was moved away from wall.
Was this instruction helpful to you?
Thank you for voting!