11047761801 Kenmore Washer - Instructions

We read your you tube instruction and followed the video

I followed your repair video explicitly, simple fix. However, one should
be careful when disconnecting the two prong electrical connector from
the heat sensor. the two black wires can pull free easily. In that case, the
rear of the female plastic wired connector must be extracted to allow the two black wires to be "pushed" into the narrow slot which displaces the
wire insulation and allows for a good electrical connection. If a punch tool is not available a pair of needle nose pliers works. Also, observe
the orientation slots on both the male andfemale connectors - they
connect one way only! I set the washer on it's face while effecting this
repair to better see what I was doing (eyesight not as good as it used to be). Thanks for the timely support!

Unplugged washer , used shop vac to drain water through drain hose on washer. Removed both hoses from old pump. Removed electric plug, removed 2 screws from bottom of the pump. Then reverse the process.

very easy repair watched videos to diagnosed problem. Removed old sensor and rubber seal replaced with new.

Son-in law did the work he was finished in about 20 minutes the repair guy wanted $249.00 to take out and put in. PLUS part.

Removed screws around door couple around hinge

just changed out the pump. easy

Unplugged the washer from electric outlet. Removed front cover by using nut driver to remove the two screws. Drained the water from the washer into a pan by loosening the cap on the filter. Removed the two hoses by compressing clamps with pliers. Unplugged the electric wire from old pump. Used screw driver to pry rubber feet of old pump loose from washer floor panel. Set old pump aside. Installed new pump using a little dish soap to help attach rubber feet to washer. Attached the two hoses using pliers. Plugged electric wire into new unit. Ran washer to check for leaks. Replaced front cover using nut driver on the two screws.

Replaced the pump. Continued to get the F9E1 error. Removed and cleaned the drain pipe between the drum and the pump. Problem resolved.

There is a video on this site that shows how to do the install. It is perfect and accurate. This pump is one of the easiest components to fix on this washer and it will save you money to do it yourself. Tech has told me twice to buy a new washer. This did the job. Make sure to take the time to fully drain the machine prior to doing this and make sure that you unplug your machine. To drain, just unscrew the cover on the front of the pump. If you start disconnecting hoses without draining you could have a mess on your hands depending on how much water is still in the washer. Use a shallow pan or bucket if your machine is on a pedestal. I have a floor drain in front of mine so I use a piece of foil to channel the water into it. After that, just do the install like the video. Also make sure to examine the reconnected hoses after you get done to make sure that they are solidly attached to the pump and that the base of the pump is tightly secured to the bottom of the machine. You have to secure the feet of the pump from the bottom which is why the video recommends putting blocks under the washer to have access to the bottom. Pump is great. Everything works well.

1. Remove bottom panel (3 screws below). 2. Remove top panel (3 screws back). 3. Remove detergent dispenser (remove T screw in front.) 4. Carefully remove control panel is plastic so be careful not to break it. 5. Pull broken bellow from front and spring loaded clamp will come lose. 6. Push away bellow. 7. Remove cables from door lock. 8. Remove front panel screws (4 - 2 on top and 2 in bottom). 9. Unscrew bellow's clamp with flat screw driver or not driver. 10. Remove worn bellow. 11. Bellow has notch on top (Use as reference to replace. 11. Clean all surfaces. 12. Install new bellow to drum. 13. Screw clamp over of bellow not too tight. Don't want to break the seat. 14. Replace all in the reverse order and for the front of the bellow refer to my previous article (story) on front latch replacement.

First I removed the retainer ring that holds the outside bellows on the frame of the front washer.
I then pushed the bellows inside of the drum of the washing machine in-order to get to the clamp that holds the bellows on the inside of the drum. To pull the clump I had to use a stubby screwdriver and socket drive to loosen the clamp. Once the clamp is loosen I was able to pull the bellows off, of the drum and out of the washing machine. Installation was the reverse of removal.

2 clamps and its off, problem is if you have average size hands you will struggle in getting the back clamp on and off.

I purchased a new bellows from this site I followed their instructions. Just tricky getting the inner clamp on aligned and tightened.

Followed internet instructions