11047576600 Kenmore Washer - Instructions

I pulled the front load washer away from the wall and unplugged. I tilted it back against the wall. I removed three screws from the lower front cover plate of washer. Once removed, I had access to the tub to pump hose which I found a small hole in. I went online to Partselect and found my part. The hose was connected in three different places by compression clamps. I then pulled the compression clamps off the connections. Cleaned up all connection points with a damp rag. Upon installation of the new tub to pump hose, I discarded the compression clamps and installed the new part using radiator clamps purchased at a auto parts store. Plugged washer back in and started a load too make sure all connections were good and tight with no leaks. After checking for leaks, I re-installed the front cover plate. Tilted washer back down being careful not too set it down hard or on my feet. Job Done....

Very --simple remove front acess panel -- open sump clean out remove water out of existing pump an hoses with small wet dry vac -- remove small wire harnes --cut band clamp on discharge with side cutter --remove inlet -suction side of pump hose clamp with channel locks --un bolt two screws on bottom side of washer with 5/16 nut runner --discard old pump reinstall new one in reverse order --only takes about 20 mins total !!! ---

I removed the three bottom screws and removed the plate. Removed the control panel, removed the star screw on the left side and pulled off the front panel of the machine. Loosen the bellow clamp with a phillips head and pull off the front spring clamp on the bellow. Pull off the old bellow and re installed the new one. Installed and tightened the bellow clamp and spring loaded clamp on the front of the bellow and re installed the panel, and control panel. Checked for leaks.

Put towel down to catch excess water, opened drain screen, used pliers to remove squeeze clamps on both hoses, removed front hold-down torx-head bolt and slid pump assembly out. Compared new part to old and found 2 differences 1:no hold-down location in front for bolt,2: the rubber padded feet are not the same. I was able to remove the two screws on the right side and use just the rubber pad for support while sliding the left side in the slot and is was plenty stable and works just fine. I guess the Whirlpool Duet model is a bit different on mounting but everything else fit quite well, the washer is working perfectly again.

First thing, unpluged the washer. I removed the lower front acces panal. I then propped the washer up on 2 pint sized paint cans to reach the pump mounting screws. I disconnected the wire bundle going to the pump. Then removed the inlet and outlet hoses from the pump. Then I removed the 2 mounting screws on bottom and slide the pump to the left and removed. I then pump the new pump on the same way I took the old one off, but in reverse. Easy and fast the worst part was the price of the pump.

Followed instructions from a You Tube video. I'd recently lost my job and money is tight and I thought we could save money doing it myself. By watching the video and ordering parts from you we were able to save $500 between parts and labor. Thanks

the hardest part of the repair is having the confidence to pull all the screws and remove door etc. Dish soap was a good trick when I needed the last bit of the bellow to pop/stretch into place in step 1 of attaching the bellow.

dryer stacked on top of washer. had to lift washer and block w/2 x 4 to get under unit and replace pump

Searched internet for diagnosis. Ran diagnostic test using the diagnostic manual from whirlpool. The error code was F29. Replaced door latch but problem was not solved. Then order the Motor Control Unit. Removed old control unit through the top by removing the top washer cover and numbering harness positions with painter's tape. Install the new Control Unit and ran diagnostic procedure. The problem was solved. The washer is working fine.

Perfect part...saved me hundreds on labor. Thanks!

Unplugged washer first! Removed front bottom panel by removing three screws, unscrewed the Drain Plug assembly by turning drain plug counter clockwise with a bucket to catch excess water from washer. Used pliers to remove spring clamps from washer agitator drain hose and then removed the spring clamp from the hose going to drain. Checked hoses for obstructions, then Slide Drain Pump assembly up to the right to remove. Then installed new Drain Pump assembly by sliding pump into slot to the left. Connected the agitator and drain hose to new Drain Pump and fastened with spring clamps. Plugged in AC line cord and turned washer on and started a quick wash cycle to check for leaks and to see if the water drained from washer properly. The water drained from washer and error code did not appear. The error code F21 reappeared during the second wash cycle. After closer inspection with a flash light, I found a large piece of cloth caught between the washer agitator and washer tub covering the drain by shining the flash light up towards the Agitator tub. This was solved by removing the Drain Pump assembly and all of the drain hoses again. Then removing the the large hose from the agitator tub and then removing the large piece of cloth from agitator tub. After reassembly, the washer worked like new!

First, I looked at a replace bellows video on U-Tube that saved a lot of time in knowing how to proceed. You really need nutdrivers as sockets won't fit on the screws. Fitting the bellows on the large drum is not as simple as it appeared in the movie. It took several attempts to get it in place, but it was simple to place the clamp after it was there. Other than that, just follow the steps in the movie for your model

First I removed the bottom panels then the door then the top then the front control panel, I had to go to different web site to get directions on how to do this, after you remove screws you have to unplug U18 from electrical control box. Then remove bumper, find wire around front of bumper and remove using needle nose pliers, then remove back of bumper from tub using phillips head screwdriver. Then with help we replaced with bumper. and put the machine back together. My complaint is there were NO instructions in the box with the bumper and the ones on your web page are not detailed enough. I had to search the web "how to remove maytag door bumper" before I found how to remove it.

removed retaining ring on front gasket, pulled gasket back, took out door lock latch, unhooked wires, then reversed method to replace.

I had to replace the bellow to the washer because I discovered the leak was from the door and bellow area, only problem I really had..... was installing the bellow on the outer drum, I applied a coat of hand soap to make it easier to secure in place.