11047751801 Kenmore Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- randy from HONEA PATH, SC
- Parts Used:
- WP8183202
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken hinge
remove door from washer and lay flat on a piece of cardboard remove 4 screws from door hinge and take out just enough screws both sides of hinge to remove hinge from pocket of door,careful not to put to much stress on glass and gasket when removing old hinge and replacing.
very simple
very simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gustavo from YOUNGSTOWN, OH
- Parts Used:
- WP8183202
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Door was not closing properly, broken swivel arm under hinge.
removed door from washer, set flat on table and just loosen up the screws all around, removed old hinge and replaced with new hinge, very easy. back to washing clothes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from LITTLETON, CO
- Parts Used:
- WPW10730972
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
pump would not pump out the water in the tub
just changed out the pump. easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from wilton manors, FL
- Parts Used:
- WPW10730972
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
The rubber boot assembly is not the same configuration as the original equipment.
I had to cut new slots in the metal base of the machine cabinet to accommodate the different configuration for the rubber boot assembly. Thankfully the new pump works like a charm.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from NEWBERG, OR
- Parts Used:
- WP8182119
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Torn bellows was leaking and eating clothes
Followed directions as shown in your repair video, having done this for the first time it took a bit longer than a repairman would have but was able to git-r-done. The most difficult part was fitting the adjustable wire back around the front of the washer, in the video it is made to look really easy however in real life it is a little more difficult and could not be attached so easily and took quite a bit of time to make sure it was attached correctly. thank you for your help.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gopaul from Queens, NY
- Parts Used:
- WP8182119
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Bellow was damaged,water leakage.
First,we took apart the front of the washer and then we removed the old bellow and put the new one on.After we put back up the front of the washer and open the door to put the clamp on then after we unlocked it.After it was working good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arthur from MORGANTOWN, PA
- Parts Used:
- WP8182119
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
The door bellows had a cut in it
I purchased a new bellows from this site I followed their instructions. Just tricky getting the inner clamp on aligned and tightened.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from BOYLSTON, MA
- Parts Used:
- WPW10730972
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
No problem as instructed.
As video instructed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WILLIAM from REPUBLIC, MO
- Parts Used:
- WP8182119
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Ripped bellowspul
Pull spring wire on front. Remove large hose lamp at tub. Reinstall in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from TARPON SPGS, FL
- Parts Used:
- W10822553
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Spring balanced tub violent shake on spin
Washer was on a 13 inch high platform I built for front.load Heat washer and dryer. Removed 3.screws from bottom of front panel and had access to all 4 shocks..front and rear. All shocks were unattachedeither at base or on tub. Easy to install all 3 from front without moving Mach. I figured if 1 or 2 shocks failed the violent.movement broke the other 2. Purrs like.a.kitten now. No bearing.or spring.damage.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from SAN MARCOS, TX
- Parts Used:
- WP8540015
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Multiple water leaks, all rubber parts are chewed up from a mouse 1/
1/4 inch nutdriver, took the top and the front panel of and renew all rubber parts / hoses. It looks less than 1 hours. All parts like factory quality, everything fits perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Casey from REXBURG, ID
- Parts Used:
- WPW10730972
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Washer would not drain flashing f-21 code
Took it old pump and replaced with new pump VERY EASY
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Helen from NASHUA, NH
- Parts Used:
- WP89503
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Leaking water inlet hoses.
Removed the old hoses and screwed on the new hoses.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lindsey from STEWART MANOR, NY
- Parts Used:
- WP8183202
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
Hinge broke
We read your you tube instruction and followed the video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- anthony from EASTPOINTE, MI
- Parts Used:
- WPW10003250
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
I was getting a sewer smell when the washer drained I did every cleaning technique and didn't solve the problem then I cleaned the inside drain hose and that helped so I replaced the hose and problem solved.
I removed the back panel to access the top end of the hose then I removed the lower front panel to access the lower end of the hose that attaches to the pump. The hose is secured with spring clamps and they were removed with pliers, the panels are secured with screws.
I replaced the hose and reinstalled the panels and I was done.
I replaced the hose and reinstalled the panels and I was done.
Was this instruction helpful to you?
Thank you for voting!