11045986403 Kenmore Washer - Instructions

Removed covers per instruction video provided by website

We do not wish to have our repair published. The part itself was perfect and corrected our leaking problem but we did have difficulty with the installation despite detailed instructions. We appreciate a good price for the perfect part!

First took a picture and printed after disconnecting machine electric supply and removing top cover. removed screw holding vale in place, removed wiring .removed valve,attached wires to new valve inserted in place attached tubing and installed mounting screw and hoses, checked all again and tested

It was fast and pretty easy to do.

disconect wayer inlet hoses.remove screws that hold the top cover. This will expose the water inlet valve. remove the defective valve and any other associated clamps,hose etc. test run for leaks.

Removed hot/cold water hoses from back of washer at water inlet valve. Pulled off top of washer by removing 3 screws at back of panel. Noted that water inlet valve had been damaged in move from storage. Pulled off 4 wires, 2 for hot and 2 for cold. Removed 1 screw holding inlet valve assembly to frame. Used pliers to release retainer ring on hose. Removed hose from valve outlet. Reversed process to install new valve.

Simple repair. #20 Torx, pair of pliers and 10 minutes to complete the job. Part was exact fit. Turned off the water supply, removed the three screws at the back, slid the top to the back and lifted it off to reveal the valve. Removed the screw holding the valve in place, slid the valve to the right and pulled the valve out to the inside. Used pliers to move the hose retainer off the valve, removed the hose, unplugged the wires, and reversed the procedure to install the new valve.

Replaced inlet valve. Took top cover off. Accessed inlet valve. Removed hoses. Replaced valve. Works like a charm.Corrected problem

Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.

Need to elongate the hole in the frame to allow the screw that holds the valve in place to be inserted. You could not even start it as is. Also it put pressure on the valve so it would not seat properly. Need to include in the instructions you may need to elongate this opening in order to complete this repair. Other than that is was extremely easy. Parts fit well. Video instructions were great. Other than not knowing about the valve screw placement changing both pieces were extremely easy. Washing machine was repaired within minutes and is functioning properly again. Even the diagnosis tool was excellent as I have no experience with repairing washing machines but your site helped me trouble shoot the issue, order the parts (and receive in a couple of days) and replace the defective pieces in minutes. Changing these 2 items got me up and running an days and cost significantly less than what a repairmen would have charged just to show up at the door. Appreciate all your help!

Shut water off to washer, unhook hoses, removed back panel of washer, removed screw that holds the valve in place then unhooked the water line that connects to the washer and removed part. Place new inlet valve in position and hooked hoses and mounted it in place, put back panel back on and hooked hoses up and turned water on. Did a test wash and it worked

so easy!!three screws to take top off,one screw held valve in take hose off then install new part and reverse take apart order and done!!!Would have been sick if had to pay service call for such a easy fix!! Mike

REMOVE HOSES AND POWER PLUG REATTACH EVERYTHING AND THEN DONE.

When I looked at the website for latch repair they showed a video (can't remember which brand but not Amana) where you had to take off the top and front of the washer to get at the latch part on the washer. For the Amana I had, you simply had to pull out a portion of the rubber gasket held onto the washer by a wire/spring combination (you can take the wire off) to get at the latch assembly. You could then undo the three screws holding the latch to the washer, pull it out and unplug the three wiring connections to remove the old latch. Then plug connections into the new latch, reinstall, tighten screws and fit gasket and wire/spring assembly back together. Much easier than going thru the top and front of the washer!

Unplug machine,remove three screws that hold on top cover.
Unplug latch switch assembly,then open front door of washing machine, remove three screws which hold latch
switch. Install in reverse order.