11027062604 Kenmore Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Julio from Prnceton, TX
- Parts Used:
- W10820048
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Shake and moved
At the time that I received the order part, Me and my Wife and 15 years old Douther got on it. We removed the very top of the counter and replaced once at the time every supension rod cleaned nice and neat. then we put the top on it's place conected the water hoses pluged it in and it was ready to roll.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shawn from Indio, CA
- Parts Used:
- W10820048
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Washer was noisy and had a lot of movement
The rod kit fixed the issue. I cant really explain how I did it, because I dint know if I did it the right way.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jose from Verobeach, FL
- Parts Used:
- W10536347
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set, Wrench set
Won't drain the water
It was not easy but I dit my sell
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tntsplace.com from MCALLEN, TX
- Parts Used:
- WP8563964
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Old hinge broke, door did not open and close right.
I removed the screws from old hinge that had broke. The piece came right out with ease. I slid the new hinge in to the hole that it went in. No struggles with ease. Lined up the screw holes and put the screws back in. Finished! Works like a charm.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Carrollton, TX
- Parts Used:
- WPW10119828, WP8563964
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Hinge pins were sheared off
I removed the screws holding the broken hinges and put the new hinges on. It only took a few minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jacob from Glennville, GA
- Parts Used:
- W10536347
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
washer would not drain water
need to get washer turned on side where you can work underneath the machine. This job is alot easy if you get where you can see good and have plenty of room to work. You have to unhoook the wire from the old pump and then take the two mounting screws off from there you unhook each hose by squeezing clamp together and sliding backwards away from pump. A pair of needle nose pliers can make this process easier if the clamps are turned in an hard to get to position. You mount the new pump the same way as taking off the damaged pump. Take a screwdriver to help you slide the clamps up onto the new pump makeing sure the sleeves are completely over the new pump fittings and the clamps are slid up evenly, so you want have any leaks. Then replaces wiring harness and mounting screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- richard from asheville, NC
- Parts Used:
- W10536347
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
replaced leaking pump
Easy repair. Went to You Tube and saw PartSelect video. The best instructions...should make a link from parts page to video of install. Also replaced Heat element on Dryer. Watched video first.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from germantown, TN
- Parts Used:
- WPW10189966
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
washer wouldn't go in the spin cycle-
Pulled washer from back of wall and disconnected power source. I removed three screws in back that houses the ol motor control board. Also, I had to pull the front control knob off so that I could lift the cover to expose control board. I took several pictures of the motor control board before unplugging the wires just in case I forgot where the wires needed to go. Very simple process and had machine working within 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- axel from lighthouse point, FL
- Parts Used:
- W10820048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
drum made loud noise
put machine on side pushed old rods out to top installed new ones. runs like new. tried to ask mechanics or stores nobody would help with info, they all want to send mechanics with 80$ just to get here. it was easy to do. thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janelle from Gray, ME
- Parts Used:
- W10536347
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
water leak at pump, crack in pump housing
First off always remember to empty all pockets, coins etc ruin pumps.shut off water supply, unhooked water lines and drain into pan.tilted machine forward so i could work on pump which is located lower left. drain pan under pump area, removed 2 rubber water hose's 3 5/16 screws with nut driver. Very carefully un clip rear of housing and removed wire harness. installed new pump
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Alvin, TX
- Parts Used:
- W10820048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The washer was trying to walk off during the spin cycle.
Well i watched a video on youtube that demonstrated the repair, and it seemed easy enough, so i ordered the parts which arrived quickly enough that we avoided a trip to the laundry mat, very cool! So i did just what they said to do, unplug machine, tape down the lid, use a putty knife to pop the retaining springs in front. I used a long screwdriver to hold up rod on top and then rotate the ball around and let the rod fall through, them i used a yard stick to pop out cup on bottom. I did have assistance holding the drum back so i could see, Then i reversed the process with a new rod. The only reason it took 30 min was i did not put the cups under the balls on top, because it didnt have them in the first place, i decided to put them in after then reading the instructions. The machine runs like new, and my wife is very happy!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kelly from Petersburg, WV
- Parts Used:
- WPW10619844
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
My lid lock assembly was bad and therefore the washer lid would not lock to allow for washing.
Went to youtube.com and watched the video that took you step by step in replacing the lid lock assembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Josh from Lodi, CA
- Parts Used:
- W10820048
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
vigoirously shaking causung UL code
Replaced rods with new set of 4
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TK from Hanford, CA
- Parts Used:
- WPW10189966
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Flashing "F1" Error Code
Had to dig a little to find what error code "F1" really meant. Thanks to the Internet. Paperwork with machine advises to call a technician. Once I discovered what the error code indicated, I followed the instructions and removed and replaced the controller. Although it was expensive I didn't have to pay for any labor. Machine now functions normally.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MEECHE from LANCASTER, SC
- Parts Used:
- W10536347
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
noisey water discharge pump
PLASTIC motor housing gets hot and become loose. causing bearing to spin and make noise . Replaced motor that was quick and simple by removing 3 screws and 2 hose clamps , pluged up motor and begain washing again with no problem . Just wish motor housing was not plastic .
Was this instruction helpful to you?
Thank you for voting!