11027087600 Kenmore Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James F Meehan from COARSEGOLD, CA
- Parts Used:
- W10536347, WPW10363893
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
the drain pump leaked water
fairly simple remove and put back in …I watched a video of a similar Maytag pump replace got some tips…the electoral connection is shielded by a pull up tab…so it was quite simple I got extra hose clamps in case?…didn’t need them
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimmy from MEMPHIS, TN
- Parts Used:
- WP89503
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Old hot water inlet hose had budge at both ends.
Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Erie, PA
- Parts Used:
- W10820039
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
The agitator was making grinding noises
Removed the softener dispenser and cap that's under it. Used 7/17" socket with an 18" long extension to reach the bolt that holds agitator down. Pulled auger off, pulled lower agitator off. Removed the 6 philips head screws that hold basket hub in place. Removed hub and installed new one, replaced screws. Lightly greased spline and reinstalled lower agitator. The auger has the cam section in it. A trick to get the rollers in place is to secure them to the cam with rubber band. Have string tied to the band. Insert the cam and when almose all the way in, pull rubber band off and the rollers stay in place. Reinstalled the bolt, cap and softener dispenser.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from Tucson, AZ
- Parts Used:
- WP8563964
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken hinge pin.
Removed broken hinge, replaced with new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elijah from Point Hope, AK
- Parts Used:
- W10193886
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set, Wrench (Adjustable)
UL flashes, will not spin, really loud,& black spots under washer
We ordered the outer tub & bearing and now the washer works like it was brand new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JESUS from PORT ARTHUR, TX
- Parts Used:
- WPW10619844
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
did not work
reemplace the lid lock assembly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from knoxville, TN
- Parts Used:
- W10183157
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set
washing machine showed F50 code
I watched a video on how to do it.it wasn't very difficult the hardest part was getting the machine out of the laundry room and laying it over
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CARROLL from HENDERSONVILLE, NC
- Parts Used:
- W10536347
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Hole in casing of drain pump due to loose nickle being pulled into pump - No screen in inlet to pump
Pulled back off of washer. Removed Spring clamps from inlet and outlet of pump housing. Removed hoses. Removed three screws holding pump in place. Disconnected electrical plug connector. Reassembled in reverse order. Note: new pump had no isolators and pump motor cover looked like a rat had chewed it up; however, motor, pump, and hoses appeared to be new. Put it on without the motor cover and it works. Epoxied the old pump housing to seal it up and now have a spare.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Demopolis, AL
- Parts Used:
- W10536347
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Washer making noise down close to bottom of machine.
First unplug electrical, disconnect all hoses. If there is a large volume of water left in the machine you need to get it out.Pull machine out so you will have room to work. Lay machine front face down. Remove drive belt, inspection cover.Take the hose clamps back up the hose,remove hoses from pump. Remove the three screws that hold the pump in place.Replace pump, take steps back as you removed the pump to restore machine to operation.Total time 45 min. I am old and slow.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Delinda M from Chicago, IL
- Parts Used:
- WPW10189966
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
f1, code on the face plate of the washer,we kept on resetting it
we ordered a motor controller,pop out the old one,then replaced it with the one we ordered,and bingo,problem is solved
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joaquin from Santa Clarita, CA
- Parts Used:
- W10820048
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Washing machine was rocking a lot, and stoping too much.
Our washer wasn't really working, we called a tech to diagnose our problem, he charged us $35 to let us know that we had a suspension problem, he promised to call us back next day with the estimate for the repair, he never did. So I decide to search, I found a video showing exactly how to do it, it was a very easy, and simple process that I decide to order the parts my self. The parts were delivered to my door in 24hrs. I installed the parts in less than 45 min, and now our washer is working like new again!!!
Thanks guys.
Thanks guys.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Houston, TX
- Parts Used:
- WPW10419333
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
machine gives uneven load alarm and f51 error code
Tilt the machine over to access the bottom I rested it on a dolly.remove the rotor with an allen wrench .then rmove the 4 bolts on the stator .then lift it off the main shaft and unlug the sensor wires . just reverse the process to install the new one (be sure to allign the arrows on the sensor and the stator when reistalling. I wish i could say this solved my problem .my machine runs untill the spin cycle then it starts shaking and gives the uneven load alarm again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Neil from Onalaska, WI
- Parts Used:
- W10536347
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench set
Water would not drain
I read the directions on this web site and was able to install the new drainage pump in about 30 minutes. I suprised myself. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jose from Verobeach, FL
- Parts Used:
- W10536347
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set, Wrench set
Won't drain the water
It was not easy but I dit my sell
Was this instruction helpful to you?
Thank you for voting!