11045081404 Kenmore Washer - Instructions

Take off top of washer and the flowmeter is in the back lefthand corner on the top of the washer. Replaced the water level switch on the top righthand of the machine also. Got about 150. 00 Total invested w/service call from local tech. F-20 has not came back yet. I hoped it fixed it washer is only 3 yrs. Old. -Gd

Easy fix,
I remove the front lower panel and the shocks where right in front of you , with a little twist with an adjustable wrench the cam right off . I removed and the replaced and it the same when you remove the back panel.
P.S when installing the shocks start by connecting to the bottom and then connect to the drum it will make it lot easier.
Good luck on your repair

Removed three screws holding the cover, then one screw holding the pump assembly in place. After unplugging the power, it took two minutes to remove the clamp-rings from the hoses. The reverse was equally idiot-proof! But THIS "idiot" had 10-thumbs which added to the time to replace the lock rings! Added an extra 5 minutes at most! _grin_

I took off the cover, removed one screw. Removed two hoses and the electrical connector. It only 5 minutes to replace the old pump with the new one.

Shut off water supply, unplug washer. Remove screws on fir the top of washer, remove supply lines for water, lift top of washer off, unclip wires going into outlet value, reclip wires into new part, put parts back into place, secure lid and hoses, turned water supple back on plug in washer and put washer back into place, there you go. Oh, one more thing, make sure you check for leaks prior to hut washer back into place. Easy as pie

Shut off water. Unplug electric. Remove top panel. Unhook hoses. Unhook tubing unplug solenoid. Use torx to remove part. Reverse steps to install new part. Replace top panel. Hook up water & electric.

First I removed the retainer ring and then pulled back enough of the boot to get the door switch out and plugged in the new switch put the retainer ring back on and it was finished. With out the repair book I would have been lost on how to do the job.

it was a really easy fix. unclamped the 2 hoses and took out screw, removed water pump. Connected two hoses back and set in place then screwed in locking screw. could not have been any easier.

Followed the installation video instructions. Removed the washer top with a 1/4” nut driver torx bit. Shut off and unhooked the water lines to the washer. Took one screw off of the solenoid valve on the washer back. Removed the water line on the solenoid on the inside with a pair of pliers. Installed the new solenoid in reverse order. It took maybe 10 minutes to take off and replace. Very easy to do.

No instructions needed. Very easy to replace. You guys are great! Much cheaper than others and delivered next day! You are now on my "favorites"!

Placed baffle inside of washer and pulled to lock into place. EASY!!!

Removed 2 screws from rear of top that hold top of washer in place, lifted top at the rear and slid it back then lifted it off. Removed the three wiring harnesses from old switch, removed the three screws holding switch in place, theses are accessed from the door opening. removed the two lower screws first and held the switch from the top while removing the last screw. Placed new switch in place and started the top screw by hand followed by hand starting the remaining two screws, tightened screws with phillips screw driver, reconnected the three harnesses, reinstalled the top and secured with the two screws. Door locks and unlocks as it is supposed to.

Replace bellow with help from Youtube video.

First,we took apart the front of the washer and then we removed the old bellow and put the new one on.After we put back up the front of the washer and open the door to put the clamp on then after we unlocked it.After it was working good as new.

REMOVE AND REPLACE. FLEXIBLE RUBBER CONNECTOR WAS NOT A EXACT REPLACEMENT, THE ORIGANIL HAD A BACK STOP VALVE, NOT SURE OF THE EFFICATE ON MACHINE.