11027092602 Kenmore Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Elijah from Point Hope, AK
- Parts Used:
- W10193886
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set, Wrench (Adjustable)
UL flashes, will not spin, really loud,& black spots under washer
We ordered the outer tub & bearing and now the washer works like it was brand new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JESUS from PORT ARTHUR, TX
- Parts Used:
- WPW10619844
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
did not work
reemplace the lid lock assembly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Houston, TX
- Parts Used:
- WPW10419333
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
machine gives uneven load alarm and f51 error code
Tilt the machine over to access the bottom I rested it on a dolly.remove the rotor with an allen wrench .then rmove the 4 bolts on the stator .then lift it off the main shaft and unlug the sensor wires . just reverse the process to install the new one (be sure to allign the arrows on the sensor and the stator when reistalling. I wish i could say this solved my problem .my machine runs untill the spin cycle then it starts shaking and gives the uneven load alarm again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Neil from Onalaska, WI
- Parts Used:
- W10536347
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench set
Water would not drain
I read the directions on this web site and was able to install the new drainage pump in about 30 minutes. I suprised myself. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Valparaiso, IN
- Parts Used:
- WPW10189966
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Socket set
Code F51 Washer would not spin.
I disassembled the top half of the machine removed the drum and found a bad bearing. The code F51 said i had a bad motor control board. I had a frozen bearing on the main shaft. Freed up bearing, machine now runs but I need to replace the bearing,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Demopolis, AL
- Parts Used:
- W10536347
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Washer making noise down close to bottom of machine.
First unplug electrical, disconnect all hoses. If there is a large volume of water left in the machine you need to get it out.Pull machine out so you will have room to work. Lay machine front face down. Remove drive belt, inspection cover.Take the hose clamps back up the hose,remove hoses from pump. Remove the three screws that hold the pump in place.Replace pump, take steps back as you removed the pump to restore machine to operation.Total time 45 min. I am old and slow.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Delinda M from Chicago, IL
- Parts Used:
- WPW10189966
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
f1, code on the face plate of the washer,we kept on resetting it
we ordered a motor controller,pop out the old one,then replaced it with the one we ordered,and bingo,problem is solved
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from knoxville, TN
- Parts Used:
- W10183157
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set
washing machine showed F50 code
I watched a video on how to do it.it wasn't very difficult the hardest part was getting the machine out of the laundry room and laying it over
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CARROLL from HENDERSONVILLE, NC
- Parts Used:
- W10536347
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Hole in casing of drain pump due to loose nickle being pulled into pump - No screen in inlet to pump
Pulled back off of washer. Removed Spring clamps from inlet and outlet of pump housing. Removed hoses. Removed three screws holding pump in place. Disconnected electrical plug connector. Reassembled in reverse order. Note: new pump had no isolators and pump motor cover looked like a rat had chewed it up; however, motor, pump, and hoses appeared to be new. Put it on without the motor cover and it works. Epoxied the old pump housing to seal it up and now have a spare.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joaquin from Santa Clarita, CA
- Parts Used:
- W10820048
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Washing machine was rocking a lot, and stoping too much.
Our washer wasn't really working, we called a tech to diagnose our problem, he charged us $35 to let us know that we had a suspension problem, he promised to call us back next day with the estimate for the repair, he never did. So I decide to search, I found a video showing exactly how to do it, it was a very easy, and simple process that I decide to order the parts my self. The parts were delivered to my door in 24hrs. I installed the parts in less than 45 min, and now our washer is working like new again!!!
Thanks guys.
Thanks guys.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bonnie from Baytown, TX
- Parts Used:
- WPW10189966
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Every wash cycle would throw out the "F1" code and I would have to keep changing the wash cycles until one would finally catch. Replaced Motor Control Board and now works excellent!
Read the previous reviews and showed my son the diagram which he then replaced the part in about 15 minutes. No more hassle and works like a charm :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- brett from seymour, IN
- Parts Used:
- W10820048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
replace suspension rods
took top off.2.replaced rods one at a time.placed top back on.very simple.evan got new bushings for the top.very simple process.no skills required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julio from Prnceton, TX
- Parts Used:
- W10820048
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Shake and moved
At the time that I received the order part, Me and my Wife and 15 years old Douther got on it. We removed the very top of the counter and replaced once at the time every supension rod cleaned nice and neat. then we put the top on it's place conected the water hoses pluged it in and it was ready to roll.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from linthicum, MD
- Parts Used:
- WPW10419333, W10183157
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Washer not rotating F 51 Code RPS Failure exhibited
1. Removed tub to ensure nothing caught to stop rotating. 2. Removed rotor and noted stator had fracture across center from coil to coil. 3. Changed stator, RPS and harness. 4. tested and received F 50 code (no rotation sensed by RPS.5. Changed RPS control board-washer works fine. Hope this repair acts as having a new washer again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Ormand Beach, FL
- Parts Used:
- W10193886
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
noisy
Removed old tub assembly and installed new tub. Job took a little longer due to first new tub arrived damaged and I had to partially reassemble machine temporarily until second tub arrived.
Was this instruction helpful to you?
Thank you for voting!